HP LH4r HP Netserver LXr 8500 Installation Guide - Page 111

Mounting the Front Bezel

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

Chapter 8 Rack Mounting the HP NetServer 9. If the Cable Management Arm installation appears to be successful, continue with the next procedure, "Mounting the Front Bezel. Mounting the Front Bezel The front bezel is attached to the HP NetServer with a hinge and a latch. The hinge and latch must be attached to the front of the HP NetServer before mounting the bezel. 1. Place the hinge into the slots on the front of the HP NetServer at the left front edge, as shown in Figure 8-13. The two hooks on the rear of the hinge must fit into the two matching holes on the front of the HP NetServer. The hooks attach the hinge to the HP NetServer, but not securely. 1. Place hinge against front of NetServer, inserting hooks into matching holes as shown. 2. Swing to left to bring it against front of NetServer Figure 8-13. Attaching the Bezel Hinge to the HP NetServer 103

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Chapter 8
Rack Mounting the HP NetServer
103
9.
If the Cable Management Arm installation appears to be successful,
continue with the next procedure, "Mounting the Front Bezel.
Mounting the Front Bezel
The front bezel is attached to the HP NetServer with a hinge and a latch. The
hinge and latch must be attached to the front of the HP NetServer before mounting
the bezel.
1.
Place the hinge into the slots on the front of the HP NetServer at the left
front edge, as shown in Figure 8-13.
The two hooks on the rear of the hinge must fit into the two matching holes
on the front of the HP NetServer. The hooks attach the hinge to the HP
NetServer, but not securely.
2. Swing to left
to bring it against
front of NetServer
1. Place hinge against
front of NetServer,
inserting hooks into
matching holes as shown.
Figure 8-13. Attaching the Bezel Hinge to the HP NetServer