HP LH4r HP Netserver LXr 8500 Installation Guide - Page 88

Processor Installation

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

Chapter 7 4 Processor Modules 1 Processor Module (min) Installing Additional Processors Right Processor Carrier Board Processor Cage Locking Bar (4) Both Cache Coherency Filters Installed (required for 8-way) Left Processor Carrier Board J6A1 Jumper Block Figure 7-3. 8-Way Configuration Processor Installation NOTE The following steps assume the HP NetServer is already in a rack. Ensure you unplug power from the HP NetServer before pulling it forward on its slides. If you have space in the rack over the HP NetServer, you may be able to install/remove processor modules without pulling the chassis out of the rack. 1. Perform the shutdown procedure listed in Chapter 3, "Opening and Closing the HP NetServer" for the respective NOS. NOTE The power supplies will continue to provide standby current to the HP NetServer until the power cable is disconnected. 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Chapter 7
Installing Additional Processors
80
Both Cache Coherency
Filters Installed
(required for 8-way)
Processor Cage
Locking Bar (4)
Right Processor
Carrier Board
Left Processor
Carrier Board
4 Processor
Modules
1 Processor
Module (min)
J6A1 Jumper Block
Figure 7-3. 8-Way Configuration
Processor Installation
NOTE
The following steps assume the HP NetServer is already in a
rack. Ensure you unplug power from the HP NetServer before
pulling it forward on its slides.
If you have space in the rack over the HP NetServer, you may
be able to install/remove processor modules without pulling the
chassis out of the rack.
1.
Perform the shutdown procedure listed in Chapter 3, "Opening and Closing
the HP NetServer" for the respective NOS.
NOTE
The power supplies will continue to provide standby current to
the HP NetServer until the power cable is disconnected.