HP LH4r HP Netserver LXr 8500 Installation Guide - Page 131

Changing the System Date and Time

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

Chapter 10 Configuring the HP NetServer NOTE To leave the dialog without entering a password, press the Esc key at any time. 6. In the Confirm New Password field, type the password again and then press the Enter key. 7. Select the Exit menu by using the right-arrow or left-arrow key. 8. Choose Exit Saving Changes from the list of exit options, and then press Enter. A dialog appears and asks you to confirm your decision. 9. Choose Yes and press the Enter key. The HP NetServer then reboots. 10. To change one of the passwords at a later date, return to the Security menu and repeat Step 4 through 9, above, for one or both passwords. NOTE The HP NetServer Utilities provide a selection to allow the user to reset their password, if they have forgotten it. The selection is titled RMC User Password Reset. This can also be done by toggling a switch, position 6 in the Configuration Switch Block on the I/O baseboard. Changing the System Date and Time To change the HP NetServer date and time, refer to the following procedure. 1. Use the right-arrow or left-arrow key to select Main from the Setup menu. As soon as you do this, the main setup screen appears. 2. Use the down-arrow key to move to the System Time field. This field actually consists of three fields: hours, minutes, and seconds. 3. Type in the hour in the hours field and press Enter to move to the minutes field. 4. Type in the minute in the minutes field and press Enter again to move to the seconds' field. 5. Type in the second in the seconds field and press Enter. 6. Leave this field using the arrow keys. 123

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Chapter 10
Configuring the HP NetServer
123
NOTE
To leave the dialog without entering a password, press the
Esc
key at any time.
6.
In the
Confirm New Password
field, type the password again and then
press the
Enter
key.
7.
Select the
Exit
menu by using the right-arrow or left-arrow key.
8. Choose
Exit Saving Changes
from the list of exit options, and then press
Enter
.
A dialog appears and asks you to confirm your decision.
9. Choose
Yes
and press the
Enter
key.
The HP NetServer then reboots.
10.
To change one of the passwords at a later date, return to the Security menu
and repeat Step 4 through 9, above, for one or both passwords.
NOTE
The HP NetServer Utilities provide a selection to allow the
user to reset their password, if they have forgotten it. The
selection is titled
RMC User Password Reset
.
This can also be done by toggling a switch, position 6 in the
Configuration Switch Block on the I/O baseboard.
Changing the System Date and Time
To change the HP NetServer date and time, refer to the following procedure.
1.
Use the right-arrow or left-arrow key to select
Main
from the Setup menu.
As soon as you do this, the main setup screen appears.
2.
Use the down-arrow key to move to the
System Time
field.
This field actually consists of three fields: hours, minutes, and seconds.
3.
Type in the hour in the
hours
field and press
Enter
to move to the
minutes
field.
4.
Type in the minute in the
minutes
field and press
Enter
again to move to
the seconds’ field.
5.
Type in the second in the
seconds
field and press
Enter
.
6.
Leave this field using the arrow keys.