HP LH4r HP Netserver LXr 8500 Installation Guide - Page 171

See

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 171 highlights

Chapter 13 Alternative Rack Mounting 3. Insert the screws through the hinge into the three holes in the HP NetServer and hand-tighten. See Figure 13-12. Looking through the open side of the hinge, you can see three raised holes for screws. These holes align with holes on the HP NetServer itself. 1. Insert screws into holes through open side of the hinge as shown. 2. Tighten screws by inserting driver through access holes in hinge as shown. Figure 13-12. Fastening the Bezel Hinge to the Chassis 4. Use the access holes in the top of the hinge to insert a driver and finish tightening the three screws. See Figure 13-12. 5. Attach the bezel latch to the HP NetServer with the screw. See Figure 13-13. The bezel latch should be in place when the HP NetServer ships, but this step is provided if it is not installed or has come loose in shipping. 163

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Chapter 13
Alternative Rack Mounting
163
3.
Insert the screws through the hinge into the three holes in the HP
NetServer and hand-tighten. See Figure 13-12.
Looking through the open side of the hinge, you can see three raised holes
for screws.
These holes align with holes on the HP NetServer itself.
2. Tighten screws by
inserting driver
through access holes
in hinge as shown.
1. Insert screws into
holes through open
side of the hinge as
shown.
Figure 13-12. Fastening the Bezel Hinge to the Chassis
4.
Use the access holes in the top of the hinge to insert a driver and finish
tightening the three screws.
See Figure 13-12.
5.
Attach the bezel latch to the HP NetServer with the screw.
See Figure 13-13.
The bezel latch should be in place when the HP NetServer ships, but this
step is provided if it is not installed or has come loose in shipping.