TASCAM SS-R200 100 SS-R200 SS-CDR200 Owners Manual - Page 30

4 − Preparations In this manual, unless otherwise specified, explanations assume that the playback mode is set to CONTINUE (continuous playback mode). Selecting tracks To select a track for playback, if the play area has more than one track, you can either skip to the previous or next track or enter a track number directly. Both methods are explained below. Skipping to the previous or next track Turn the MULTI JOG dial (or press the remote control SKIP . and / buttons) to skip to the previous or next track. • Turn the MULTI JOG dial right to skip to the next track or to the left to skip to the previous track. • Press the remote control SKIP / button to skip to the next track or . button to skip to the previous track. After selecting the track, press the front panel or remote control PLAY button to start track playback. Alternatively, instead of pressing the front panel or remote control PLAY button, press the front panel or remote control READY button to start playback standby at the beginning of the selected track. Specifying a track number You can use the remote's number buttons to directly enter the number of the track that you want to play. For audio format CDs, the track number will be a maximum of two digits. For MP3 and WAV format media, the track number will be a maximum of three digits. 1 Use the remote's number buttons to input the track number. Enter the track number starting with the highest digit. Example 1: For track 1, press 1 Example 2: For track 12, press 1 followed by 2 Example 3: For track 103 press 1 followed by 0 and then 3 2 Press the front panel or remote control PLAY button to start playback of the selected track. Alternatively, instead of pressing the front panel or remote control PLAY button, press the front panel or remote control READY button to start playback standby at the beginning of the selected track. NOTE • Instead of pressing the front panel or remote control PLAY button, you can also press the MULTI JOG dial or remote control ENTER button to start playback of the selected track. • You cannot use the number buttons on the remote to specify the track while in program or random mode. 30 TASCAM SS-CDR200/SS-R200/SS-R100 Searching backward and forward You can search forward or backward in a track while listening to the audio. 1 Play the desired track or put it into playback standby. 2 Press and hold the m [SKIP] or , [LOCK] button (or remote control SEARCH m or , button) to start searching backward or forward. 3 To stop searching, release the button you are holding. The unit will return to the state (playback standby or playback) it was in before searching. Time search When the unit is stopped, in playback standby or playing, you can locate to a specified time in the specified track. NOTE You cannot use time search when the play mode is PROGRAM or RANDOM. Use the remote control number buttons to input numbers in the following order. • Track number: 3 digits • Elapsed time from the beginning of the track: two digits each hours, minutes, seconds For example, if you want to specify a location that is 1 minute 30 seconds from the beginning of track 2, you would press keys in the following order. 0 q 0 q 2 q 0 q 0 q 0 q 1 q 3 q 0 When you finish entering the nine digits, the unit 
will automatically locate to the specified position. If the unit was stopped or playing back before locating to the time, playback will begin after locating. If the unit was in playback standby prior to locating to the time, it will resume playback standby after locating. If you specify a track number that does not exist in the current play area or a time that does not exist in the track, the operation will be cancelled at that point. Time searching after partial entry If you press the remote's ENTER, PLAY or READY button before you finish entering the time, you will locate to the position that is specified at that point. For example, suppose you intend to specify a location that is 12 minutes from the beginning of track 2, but do not complete the entry, inputting only: 0 q 0 q 2 q 0 q 0 q 1 q 2 Then, if you press the remote control ENTER, PLAY or READY button, the unit will locate to 12 minutes after the beginning of track 2. The button you push will determine what happens after locating.