TRENDnet TEW-829DRU Users Guide - Page 36

OSPF (Open Shortest Path First), Point to Point

Get TRENDnet TEW-829DRU PDF manuals and user guides View all TRENDnet TEW-829DRU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

TRENDnet User's Guide OSPF (Open Shortest Path First) Network > Routing > OSPF 1. Log into your router management page (see "Access your router management page" on page 8). 2. Click on Network, click on Routing, and click on the OSPF tab. 3. Review the OSPF Routing section. To save changes to this section, click Apply to commit and save your changes. In the Overview table, you can enable and configure RIP for each interface by clicking Edit next to the interface.  OSPF enable: Check the option to enable OSPF dynamic routing globally on the router.  Router ID: Enter the OSPF router ID. Limited Warranty  OSPF enable: Check the option to enable OSPF dynamic routing on the specified interface.  Network type: Select the OSPF network type. Select only Point to Point or Point to Multi-point if connecting to your networking using PPP protocol, otherwise select Broadcast. If only exchanging OSPF routing information to one other device, select Non-Broadcast and enter in the Neighbor IP address at the bottom.  Key authentication - Enables MD5 authentication on all OSPF messages sent and received.  Key string - If authentication is enabled, enter the authentication key string/password to use for OSPF messages sent and received.  Plain text password - This option will set the password to be send in clear text instead of using the MD5 hash. This setting is not recommended.  Cost - Enter the OSPF cost value.  Priority - Enter the OSPF priority value.  Area - Enter the area id for OSPF. You can check the current routing table under Status > Routes under Active IPv6Routes. © Copyright 2019 TRENDnet. All Rights Reserved. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
© Copyright 2019 TRENDnet. All Rights Reserved.
29
TRENDnet User’s Guide
Limited Warranty
OSPF (Open Shortest Path First)
Network > Routing > OSPF
1. Log into your
router management page (see “
Access your router management page
”
on page 8).
2. Click on
Network,
click on
Routing,
and click on
the
OSPF
tab.
3. Review the OSPF Routing section. To save changes to this section, click
Apply
to
commit and save your changes.
In the
Overview
table, you can enable and configure RIP for each interface by clicking
Edit
next to the interface.
OSPF enable:
Check the option to enable OSPF dynamic routing globally on the
router.
Router ID:
Enter the OSPF router ID.
OSPF enable:
Check the option to enable OSPF dynamic routing on the specified
interface.
Network type:
Select the OSPF network type. Select only
Point to Point
or
Point
to Multi-point
if connecting to your networking using PPP protocol, otherwise
select
Broadcast
. If only exchanging OSPF routing information to one other
device, select
Non-Broadcast
and enter in the
Neighbor
IP address at the bottom.
Key authentication
–
Enables MD5 authentication on all OSPF messages sent and
received.
Key string
–
If authentication is enabled, enter the authentication key
string/password to use for OSPF messages sent and received.
Plain text password
–
This option will set the password to be send in clear text
instead of using the MD5 hash. This setting is not recommended.
Cost
–
Enter the OSPF cost value.
Priority
–
Enter the OSPF priority value.
Area
- Enter the area id for OSPF.
You can check the current routing table under
Status > Routes
under
Active IPv6-
Routes.