TRENDnet TEW-829DRU Users Guide - Page 62

Multiple WAN Management Settings, MWAN Status

Get TRENDnet TEW-829DRU PDF manuals and user guides View all TRENDnet TEW-829DRU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

TRENDnet User's Guide Multiple WAN Configuration Limited Warranty MWAN Status  Interface Live Status - This section displays the current status of the WAN interfaces of your router. Tracking is enabled using physical link status and L2 based methods but the tracking status displayed refers to the status of IP based link tracking which can be configured under the Link Tracking section. Multiple WAN Management Settings Network > Multiple WAN The section provides an overview of the multiple WAN management settings and the dual WAN mode functionality. 1. Log into your router management page (see "Access your router management page" on page 8). 2. Click on Network and click on Multiple WAN. 3. Review the settings below. When complete, click Apply to save and commit your changes. Note: Multiple WAN diagnostics can be used under Administrator > Diagnostics under the MWAN Interface Diagnostics section. Link Tracking - Allows you to setup WAN link tracking by pinging Internet IP addresses.  Enable Tracking - Checking this option enables IP based WAN link tracking on the specific WAN interface.  Tracking IP - Enter an Internet IP address to send ping requests used to verify the link status of a specific WAN interface. You can add additional IP address by clicking .  Ping Interval - Click the drop-down list to set the time interval between consecutive ping requests.  Fail Count - Click the drop-down list to set the maximum number of failed ping requests before interface status is considered to be down or failed. © Copyright 2019 TRENDnet. All Rights Reserved. 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
© Copyright 2019 TRENDnet. All Rights Reserved.
55
TRENDnet User’s Guide
Limited Warranty
Multiple WAN Configuration
Multiple WAN Management Settings
Network > Multiple WAN
The section provides an overview of the multiple WAN management settings and the
dual WAN mode functionality.
1. Log into your router management page (see “
Access your router management page
”
on page 8).
2. Click on
Network
and click on
Multiple WAN.
3. Review the settings below. When complete, click
Apply
to save and commit your
changes.
Note:
Multiple WAN diagnostics can be used under Administrator > Diagnostics under
the MWAN Interface Diagnostics section.
MWAN Status
Interface Live Status
–
This section displays the current status of the WAN
interfaces of your router. Tracking is enabled using physical link status and L2 based
methods but the tracking status displayed refers to the status of IP based link
tracking which can be configured under the Link Tracking section.
Link Tracking
–
Allows you to setup WAN link tracking by pinging Internet IP addresses.
Enable Tracking
–
Checking this option enables IP based WAN link tracking on the
specific WAN interface.
Tracking IP
–
Enter an Internet IP address to send ping requests used to verify the
link status of a specific WAN interface. You can add additional IP address by clicking
.
Ping Interval
–
Click the drop-down list to set the time interval between
consecutive ping requests.
Fail Count
–
Click the drop-down list to set the maximum number of failed ping
requests before interface status is considered to be down or failed.