HP 450c Service Manual - Page 128

Installing a RAM or ROM SIMM, A RAM SIMM provides the Printer with extra memory. A ROM SIMM

Get HP 450c - DesignJet Color Inkjet Printer PDF manuals and user guides View all HP 450c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 128 highlights

Installing a RAM or ROM SIMM A RAM SIMM provides the Printer with extra memory. A ROM SIMM contains new firmware code to override the internal firmware code. 1. Make sure that the Printer is switched OFF and that neither the power cord nor an interface cable is connected. 2. Unscrew the cover plate and the cable clip at the back of the Printer, and remove it. Torx-10 or Flat Before handling a SIMM, either put on a grounding wrist strap and attach the end to the metal chassis of the Printer, or touch the outer metal surface of the Printer with your hand. Otherwise, static electricity from your body could damage the SIMM. 3. Take the SIMM out of its bag, holding the SIMM only by the edges. 4. With the SIMM's small notch on the left and the metallic edge away from you, load the SIMM into the slot: D nearest to you (RAM SIMM). D furthest from you (ROM SIMM). To do this, first hold the SIMM at an angle, and then gradually push it back until it clicks vertically into place. Notch 2 1 5. Replace the cover plate, the cable clip (held by the left screw) and the screws. 8-6 HP DesignJet 430, 450C and 455CA Printers Removal and Installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
8-6
Removal and Installation
HP DesignJet 430, 450C and 455CA Printers
Installing a RAM or ROM SIMM
A RAM SIMM provides the Printer with extra memory. A ROM SIMM
contains new firmware code to override the internal firmware code.
1.
Make sure that the Printer is switched OFF and that neither the power
cord nor an interface cable is connected.
2.
Unscrew the cover plate and the cable clip at the back of the Printer, and
remove it.
Torx-10
or
Flat
Before handling a SIMM, either put on a grounding wrist strap and
attach the end to the metal chassis of the Printer, or touch the outer
metal surface of the Printer with your hand. Otherwise, static
electricity from your body could damage the SIMM.
3.
Take the SIMM out of its bag, holding the SIMM only by the edges.
4.
With the SIMM's small notch on the left and the metallic edge away from
you, load the SIMM into the slot:
D
nearest to you (RAM SIMM).
D
furthest from you (ROM SIMM).
To do this, first hold the SIMM at an angle, and then gradually push it
back until it clicks vertically into place.
1
2
Notch
5.
Replace the cover plate, the cable clip (held by the left screw) and the screws.