HP 450c Service Manual - Page 45

If the test fails, to resolve the problem, try one of the following - designjet carriage belt

Page 45 highlights

If the test fails, to resolve the problem, try one of the following: 1 Clear any binding due to a media jam. 2 Turn the Printer off. Manually move the carriage along the carriage axis. Check for any areas where the carriage may be binding. 3 Ensure that the belt and belt pulley are in correct working order. Remove dirt from the pulley that could cause the belt to slip. 4 Remove dirt from the slider rod and chassis beam. Apply oil (Anderol 4068, HP part number: 6040Ć0858) to the carriage bushings. 5 At high temperatures, and if the fan is not working correctly, the internal resistance of the motor driver may increase, causing a decrease in the voltage between the motor contacts, and a shutdown of the motor. 6 Ensure that the encoder strip is not inverted, damaged or absent. 7 Reconnect or replace the trailing cable ' page 8Ć8. 8 Replace the carriage assembly ' page 8Ć37. Only replace one component at a time and perform the test again before replacing another component. Using this procedure you will be able to determine exactly which component failed. Service Tests HP DesignJet 430, 450C and 455CA Printers 4-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208

Service Tests
4-11
HP DesignJet 430, 450C and 455CA Printers
If the test fails,
to resolve the problem, try one of the following:
1
Clear any binding due to a media jam.
2
Turn the Printer off. Manually move the carriage along the carriage axis.
Check for any areas where the carriage may be binding.
3
Ensure that the belt and belt pulley are in correct working order. Remove
dirt from the pulley that could cause the belt to slip.
4
Remove dirt from the slider rod and chassis beam. Apply oil (Anderol
4068, HP part number: 6040Ć0858) to the carriage bushings.
5
At high temperatures, and if the fan is not working correctly, the internal
resistance of the motor driver may increase, causing a decrease in the
voltage between the motor contacts, and a shutdown of the motor.
6
Ensure that the encoder strip is not inverted, damaged or absent.
7
Reconnect or replace the trailing cable
'
page 8Ć8.
8
Replace the carriage assembly
'
page 8Ć37.
Only replace one component at a time and perform the test
again before replacing another component. Using this procedure
you will be able to determine exactly which component failed.