Yamaha A5000 Owner's Manual - Page 108

PLAY-SETUP Knob 5 [ Turn] AD Input-R Pan (A/D Input Right Pan) Specifies the output pan position of the signal received via the "R" A/D input jack. [Range] -63 - +63 Positive values set pan to the right; negative values set pan to the left. • When "L/R" or "L+R" is selected as the AD Input Source, the ADInput-Lpan setting applies to both channels and thus the ADInput-Rpan parameter cannot be edited. [ Press] QUICK... Calls the quick entry menu (page 83). Cursor w Cursor w Turn action Press action Knob 1 Cursor/Page Tree View Knob 2 ADInput-L Output1 - Knob 3 ADInput-L Output Level1 QUICK... Knob 4 ADInput-L Output2 - Knob 5 ADInput-L Output Level2 QUICK... Knob 1 Same function as Cursor q (page 107). Knob 2 [ Turn] ADInput-L Output1 (A/D Input Left Output 1) Sets the output destination of the signal received at the "L" A/D input jack. [Range] off, StereoOut, AsgnOutL&R, AsgnOut1&2, AsgnOut3&4, AsgnOut5&6, DIG&OPT, Ef1 - Ef6 (Ef1 - Ef3 on the A4000) • StereoOut ... Output is sent to the rear-panel STEREO OUT jacks as well as the front-panel PHONES jack. • AsgnOutL&R ... The rear-panel assignable output jacks. • AsgnOut1&2, AsgnOut3&4, AsgnOut5&6 ... The corresponding assignable outputs on the optional AIEB1 I/O expansion board. • DIG&OPT ... The coaxial and optical digital outputs on the optional AIEB1 I/O expansion board. • Ef1 - Ef6 ... Output is routed to the specified effect. Knob 3 [ Turn] ADInput-L Output Level1 (A/D Input Left Output Level 1) Sets the level of the signal sent to the output destination specified by the ADInput-LOutput1 parameter. [Range] 0 - 127 [ Press] QUICK... Calls the quick entry menu (page 83). • When both the Output1 and Output 2 parameters are set to the same output destination, the higher of the two output level settings (Output Level 1 and Output Level2) will take priority. Knob 4 [ Turn] ADInput-L Output2 (A/D Input Left Output 2) Sets the output destination of the signal received at the "L" A/D input jack. [Range] off, StereoOut, AsgnOutL&R, AsgnOut1&2, AsgnOut3&4, AsgnOut5&6, DIG&OPT, Ef1 - Ef6 (Ef1 - Ef3 on the A4000) The settings are the same as for the ADInput-L Output1 parameter (page 108). Knob 5 [ Turn] ADInput-L Output Level2 (A/D Input Left Output Level 2) Sets the level of the signal sent to the output destination specified by the ADInput-L Output2 parameter. [Range] 0 - 127 [ Press] QUICK... Calls the quick entry menu (page 83). • When both the Output1 and Output 2 parameters are set to the same output destination, the higher of the two output level settings (Output Level 1 and Output Level2) will take priority. Cursor e Cursor e Turn action Press action Knob 1 Cursor/Page Tree View Knob 2 ADInput-R Output1 - Knob 3 ADInput-R Output Level1 QUICK... Knob 4 ADInput-R Output2 - Knob 5 ADInput-R Output Level2 QUICK... Knob 1 Same function as Cursor q (page 107). 108 Chapter 4 PLAY Mode • A5000/A4000 q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q