Yamaha A5000 Owner's Manual - Page 154
Display], Knob 1, Recording-setup
View all Yamaha A5000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 154 highlights
RECORDING-SETUP • NewSB ... A new sample bank is automatically created and new samples are automatically assigned to that sample bank. The new sample bank is automatically assigned to the curently selected program. * NewSB can only be selected when the New+ Record Type is selected. • This is handy when you want to assign a number of sequentially recorded samples to the same sample bank. [DISPLAY] q A number of recording parameters set via the SETUP display are shown here. w An input signal level meter with markers for the start and stop edge levels set via the TRIGGER display. Knob 3 [ Turn] Original Key Turn the knob to set the sample's "original key" - the key that best represents the sample's inherent pitch. [Range] C-2 - G8 • If the Note Display Type utility (UTILITY-SYSTEMCustom) (page 198) is set to "name" the parameter will be displayed as note names such as "C3." If set to "number" the parameter will be displayed as MIDI note numbers such as "60." • The key range cannot be set if the Record Type is set to Replc (the settings of the selected sample are used). [ Press] MIDI When this knob is pressed the parameter can be directly set by a MIDI message received from an external MIDI device (page 82). Cursor w Cursor w Turn action Press action Knob 1 Cursor/Page Tree View Knob 2 Key Map MONITOR Knob 3 Original Key MIDI Knob 4 Low Key / No function MIDI / No function Knob 5 High Key / Map Key MIDI / No function Knob 1 Same function as Cursor q (page 153). Knob 2 [ Turn] Key Map Specifies the key mapping method for the new sample. [Range] Manual, Auto • Manual ... Key mapping for the new sample is setup via Knobs 3 through 5: Original Key, Low Key, and High Key. • Auto ... The original key of the new sample is determined by the Knob 3 (Original Key) setting, and the Key Range Low and High values are set to =Orig (i.e. the same as the original key). When a number of samples are recorded sequentially the originally key is automatically shifted upward by one note for each sample. • When the New+ Record Type is selected (sequential recording) and Key Map is set to Auto, the original key of each new sample recorded is automatically shifted up one note. • This parameter cannot be set when the Record Type is set to Replc. [ Press] MONITOR Pressing this knob alternately turns the MONITOR function on and off. A speaker icon appears above Knob 2 when the MONITOR function is turned on. When Key Map (Knob 2) Is Set To Manual Knob 4 [ Turn] Low Key Turn the knob to set the low end for the sample's key range. [Range] =Orig, C-2 - G8 • =Orig ... The original key value is used. • C-2 - G8 ... The Low Key is set to the corresponding note. Low Key cannot be set to a note higher than the High Key. • The key range cannot be set if the Record Type is set to Replc (the settings of the selected sample are used). [ Press] MIDI When this knob is pressed the parameter can be directly set by a MIDI message received from an external MIDI device (page 82). Knob 5 [ Turn] High Key Turn the knob to set the high end for the sample's key range. [Range] C-2 - G8, =Orig. • C-2 - G8 ... The High Key is set to the corresponding note. High Key cannot be set to a note lower than the Low Key. • =Orig ... The original key value is used. • The key range cannot be set if the Record Type is set to Replc (the settings of the selected sample are used). [ Press] MIDI When this knob is pressed the parameter can be directly set by a MIDI message received from an external MIDI device (page 82). 154 Chapter 6 RECORD Mode • A5000/A4000 q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q