Yamaha A5000 Owner's Manual - Page 183
Press] EXEC&CONT Execute & Continue, DISK Mode
View all Yamaha A5000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 183 highlights
7. DISK COMMANDS Cursor q Cursor q [ Press] EXEC&CONT (Execute & Continue) Press this knob to call the backup confirmation display. Press Knob 5 (YES) to actually execute the backup operation. Cursor w Turn action Press action Knob 1 Cursor EXEC Knob 2 - - Knob 3 - Knob 4 Knob 5 CDR DriveID Write Speed RW-ERASE TEST EXEC&CONT Cursor w Knob 1 [ Turn] Cursor Positions the cursor. [ Press] EXEC (Execute) Press this knob to call the backup confirmation display. Press Knob 5 (YES) to actually execute the backup operation. Knob 3 [ Press] RW-ERASE (CD-RW Erase) Erase all data from a CD-RW disk to allow further recording. • Depending on the CD-RW drive being used, this process may take some time. Knob 4 [ Turn] CDR DriveID Selects the drive ID of the CD-R or CD-RW drive to which the data is to be backed up. When a CD-R or CD-RW drive is selected, the drive's maker and product number will be displayed. [Range] SCSI 0 - SCSI 7 • If a connected CD-R or CD-RW drive cannot be selected, go to the disk select display (DISK-DISKDisk) and check the mount/unmount status and SCSI ID settings of the device (page 173). [ Press] TEST Executes a data transfer test for the selected CD-R or CD-RW drive. A disk must be loaded in the drive before the test can be initiated, but no data will be written to the disk. • If the test produces an error, choose the next slowest write speed (Knob 5) and run the test again. The write speed setting is appropriate if the test produces no errors. Use the error-free write speed when actually writing to a disk. • The data transfer test will take as long as actually writing to the disk, but since a CD-R disk will become unusable if an error occurs while actually writing to it, it is advisable to run the test to check for potential errors before actually writing the data. Knob 5 [ Turn] Write Speed Selects the CD-R/CD-RW write speed. [Range] x1, x2, x4, x6, x8 Turn action Press action Knob 1 Cursor EXEC Knob 2 Backup# - Knob 3 - RW-ERASE Knob 4 Disk TEST Knob 5 - EXEC&CONT Knob 1 Same function as Cursor q (page 183). Knob 2 [ Turn] Backup # (Backup Number) Selects a line in the disk backup list. [Range] 1 - 8 • "End of List" will appear at the first line number for which a disk or volume has not been selected. Line numbers past the "End of List" line cannot be selected. For this reason, line numbers 2 and higher cannot be selected when no disk or volume selections have been made. • Disks listed up to the "End of List" line will be backed up. Knob 3 Same function as Cursor q (page 183). Knob 4 [ Turn] Disk Specifies a disk to be backed up for the currently selected backup number (Knob 2). [Range] All connected/mounted disks. • If a connected SCSI or IDE device (hard disk, ZIP drive, etc.) cannot be selected, go to the disk select display (DISK-DISK-Disk) and check the mount/ unmount status and SCSI ID settings of the device (page 173). [ Press] TEST Executes a data transfer test for the selected CD-R or CD-RW drive. A disk must be loaded in the drive before the test can be initiated, but no data will be written to the disk. • If the test produces an error, choose the next slowest write speed (Knob 5) and run the test again. The write speed setting is appropriate if the test produces no errors. Use the error-free write speed when actually writing to a disk. 183 q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q A5000/A4000 • Chapter 7 DISK Mode