Yamaha A5000 Owner's Manual - Page 269

Effect Parameter List

● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●

A5000/A4000 •

Appendix

269

93: TEMPO AUTO WAH

1

LFO Depth

0 — 127

Wow filter control depth

2

LFO Frequency

32nd note — 1/4 note x 16

Wow filter control frequency (specified by note length)

3

Cutoff Freq Offset

0 — 127

Wow filter control frequency offset

4

Resonance

1 — 12.0

Wow filter bandwidth

@5

LFO Init Phase

0deg, 90deg, 180deg, 270deg

Sets the initial phase of the LFO waveform

6

EQ Low Frequency

32Hz — 2.0kHz

Frequency at which the EQ will boost/cut the low range

7

EQ Low Gain

-12dB — +12dB

Gain with which the EQ will boost/cut the low range

8

EQ High Frequency

500Hz — 16.0kHz

Frequency at which the EQ will boost/cut the high range

9

EQ High Gain

-12dB — +12dB

Gain with which the EQ will boost/cut the high range

10

Dry/Wet Balance

D63>W — D=W — D<W63

Balance of the dry sound and effect sound

11

LFO Reset (Ctrl)

Reset to initial phase (for MIDI control)

Synchronizes to external MIDI clock when Program LFO sync is set to “MIDI,” and to the Program LFO tempo when set to “Manual.”

The initial phase of the LFO modulation waveform can be reset from a MIDI controller.

In order to do this the controller to be used must be assigned to “E*-11” (“*” is the effect number used for this effect) via the program controller setup display. The phase is reset when

a corresponding MIDI control change message is received, regardless of the control change value.

94: TEMPO DIGITAL SCRATCH

1

Input Level

0 — 127

The degree of scratch effect

2

Initial Delay

0.1 — 460.0ms

Delay time

3

Scratch Speed


Scratch modulation frequency (specified by note length)

4

Scratch Depth

0 — 127

Scratch modulation depth

5

Scrch LFO Init Phase


Initial phase setting (Scratch LFO)

6

Auto Pan Speed


Auto-pan frequency (specified by note length)

7

Auto Pan Depth

0 — 127

Auto-pan depth

8

Pan LFO Init Phase


Initial phase setting (Pan LFO)

9

EQ Frequency

100Hz — 10.0kHz

Frequency at which the EQ will boost/cut the mid range

10

EQ Gain

-12 — +12dB

Gain with which the EQ will boost/cut the mid range

11

EQ Width

1.0 — 12.0

Width of the mid range area which the EQ will boost/cut

12

HPF Frequency

thru, 20Hz — 8.0kHz

Frequency at which the high pass filter will cut the low range

13

Dry/Wet Balance

D63>W — D=W — D<W63


14

Scrch LFO Reset (Ctrl)


15

Pan LFO Reset (Ctrl)



The initial phase of the LFO modulation and pan waveforms can be reset from a MIDI controller.

In order to do this the controller to be used must be assigned to “E*-14” or “E*-15” (“*” is the effect number used for this effect) via the program controller setup display. The phase is

reset when a corresponding MIDI control change message is received, regardless of the control change value.

95: TEMPO AUTO SYNTH

1

Mod Speed

0 — 127

Modulation speed

2

Mod Wave Type

TypeA,TypeB,TypeC,TypeD

Modulation type

3

Mod Depth

0 — 127

Modulation depth

4

Mod Depth Ofst R

-63 — +63

Modulation depth in relation to right-channel offset

5

LPF Frequency

1.0kHz — 18.0kHz,thru

Frequency at which the low pass filter will cut the high range

6

HPF Frequency

thru,22Hz — 8.0kHz

Frequency at which the high pass filter will cut the low range

7

Delay Time

0.1 — 370.0ms

Delay time

8

Delay Time Ofst R

0 — -884

Offset of R ch delay time

9

Feedback Level

-63 — +63

Feedback amount

10

Delay Level

0 — 127

Delay level

11

AM Speed


Modulation frequency specified by note length

12

AM Wave

tri,sine,saw up,saw down

Modulation waveform

13

AM Depth

0 — 127

Amplitude modulation depth

14

AM Inverse R

normal,inverse

Inverts the phase of the left and right channels of the modulation waveform

15

AM Init Phase


Sets the initial phase of the modulation waveform

16

AM Reset (Ctrl)






96: TEMPO FLANGING PAN

1

Dry/Wet Balance

D63>W — D=W — D<W63


2

Flanger&Pan Speed


Delay modulation frequency specified by note length

3

Flanger Depth

0 — 127

Delay modulation depth

4

Flanger Delay

0.1 — 180.0ms

Delay time

5

Flanger Feedback

-63 — +63

Feedback amount

6

FlgPan Delay

0.1 — 180.0ms

Delay time

7

FlgPan Feedback

-63 — +63

Feedback amount

@8

LFO Init Phase


Sets the initial phase of the LFO waveform

9

LPF Frequency

1.0kHz — 18.0kHz,thru

Frequency at which the low pass filter will cut the high range

10

Delay Time

32th note — 1/4 note

Delay time specified by note length

11

Delay Feedback

-63 — +63

Feedback amount

12

Delay Level

0 — 127

Delay level

13

AM Speed


Amplitude modulation frequency specified by note length

14

AM Depth

0 — 127

Amplitude modulation depth

15

AM Init Phase


Sets the initial phase of the modulation waveform

16

LFO Reset (Ctrl)






Yamaha A5000 Owner's Manual - Page 269

Tempo Auto Wah, Tempo Digital Scratch, Tempo Auto Synth, Tempo Flanging Pan

Page 269 highlights

Section	Page
Cover	1
List of Accessories	4
Features	5
Using the Manual	6
Manual Organization	6
Finding Information You Need	6
Other Conventions	7
Contents	8
Panel and Connector Arrangement	10
A5000/A4000 Options	14
Handling the Floppy Disk Drive(FDD) and Floppy Disk	15
Chapter 1 Setting Up	17
Setup Procedure	18
Power Connection	19
Audio Output Connections	20
Audio Input Connections	23
MIDI Connections	25
Powering On and Off	27
Sound Check	28
Chapter 2 Sampler Basics & Essential Procedures	31
SAMPLER BASICS	32
ESSENTIAL PROCEDURES	37
Chapter 3 The A5000/A4000 System & Features	57
1. System Overview	58
Internal Structure	58
Sampling Tone Generator	59
The Effect Stage	63
Total EQ	64
Controllers	64
Sequencer	64
I/O Interface	65
Data Organization & Management	65
2. The A5000/A4000 Functions	68
A5000/A4000 Mode Organization	68
Function Tree	73
3. Basic Operation	77
Common Mode Display Features	77
Selecting Modes & Functions	77
Selecting Display Pages	78
Editing Parameters	79
Executing Functions	80
Command Selection	80
Character Entry	81
MIDI Input	82
QUICK Entry	83
Tree View Display	83
A/D Input	85
MIDI Indicator	85
Shortcut Operation	86
Special Button Functions	86
Factory Reset	86
Chapter 4 PLAY Mode	87
About the PLAY Mode	88
1. PROGRAM	89
Program Select	89
Program Mix	90
Program Portamento	91
2. SAMPLE	93
Select Sample	93
Select Sample from Sample Bank	95
3. EASY EDIT	96
Mix	96
Output	97
Out & Gain	97
Filter	98
Pitch	98
Amplitude EG	99
Key	99
Velocity	100
Crossfade	100
Control	101
4. EFFECT	102
Effect Setup A	102
Effect Setup B	104
Effect Edit	104
5. SETUP	107
S/H Speed	107
AD Input	107
6. CONTROL	110
Program Controller A/B	110
Channel Setup	112
Program LFO	113
Chapter 5 EDIT Mode	117
About the EDIT Mode	118
1. TRIM/LOOP	120
Waveform	120
Sample Information	124
Loop Remix	125
2. MAP/OUT	127
Mix & Key Range	127
Pitch	129
Expand & Velocity Range	131
Level Scaling	132
3. FILTER	133
Filter & EQ	133
Filter Scaling	135
4. EG	137
Amplitude EG	137
Filter EG	138
Pitch EG	140
5. LFO	143
LFO	143
6. MIDI/CTRL	145
MIDI Set	145
Sample Controller A & B	146
Chapter 6 RECORD Mode	149
About the RECORD Mode	150
1. RECORD	151
Record	151
2. SETUP	153
Record Setup	153
Process	157
3. TRIGGER	158
Trigger	158
4. EFFECT	160
Recording Effect Setup	160
Recording Effect Edit	160
5. EXT CTRL (External Control)	161
CD-DA Control	161
6. MONITOR	163
Monitor & Click	163
Chapter 7 DISK Mode	165
About the DISK Mode	166
1. PROGRAM	167
PgmLoad	167
2. SAMPLE	169
SmpLoad	169
3. SEQUENCE	171
SeqLoad	171
4. VOLUME	172
Volume	172
5. DISK	173
Disk Select	173
Disk Setup	173
6. IMPORT	175
Import	175
7. DISK COMMANDS	177
Selecting a Command	177
Command Execution	177
SAVE	177
FORMAT	177
COPY VOLUME	181
SYSTEM FILE	182
BACKUP	182
CD-DA	184
LOAD OS	185
Chapter 8 UTILITY Mode	187
About the UTILITY Mode	188
1. TOTAL EQ	189
Total Equalizer	189
2. PANEL PLAY	191
Knob Controller	191
Knob Controller Setup	191
Function Key Play Setup	192
3. SEQUENCE	194
Sequence	194
4. MASTER	195
Tuning	195
Output	195
5. SYSTEM	197
KeysSet	197
Customise	198
6. MIDI	200
Channel Message	200
System Exclusive	201
Chapter 9 COMMAND	203
About the COMMANDS	204
Selecting a Command	206
Command Execution	206
COPY	206
DELETE	208
SAVE	208
ARRANGE	211
FREEZE	212
REGISTER	214
BULK DUMP	216
INITIALIZE	217
PROCESS	218
LOOP DIVIDE	221
RESAMPLE	222
STEREO -> MONO	225
MOVE	226
CREATE OSC	227
EXPORT	228
REVERT	230
Appendix	231
Installing Optional Equipment	232
Removing the Top Cover	232
Replacing the Top Cover	233
Installing SIMMs	234
Installing the AIEB1 I/O Expansion Board	237
Installing an Internal SCSI Hard Disk	240
Installing an Internal IDE Hard Disk	244
Installing an ATAPI ZIP Drive	247
Connecting external SCSI devices	251
Specifications	254
Effect Type List	256
Effect Parameter List	258
Control Change Number List	270
Troubleshooting	271
Error Messages	273
MIDI Data Format	274
A5000/A4000 MIDI Implementation Chart	286