Home » Yamaha Manuals » Musical Instruments » Yamaha A5000 » Manual Viewer

Yamaha A5000 Owner's Manual - Page 40

Go To the Record Trigger Display, Set the AD Input Gain, Set the Trigger Options

Get Yamaha A5000 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

ESSENTIAL PROCEDURES 8. Go To the Record Trigger Display Press the [TRIGGER] function key to go to the "REC-Trigger" display. 9. Set the AD Input Gain This is not necessary if you're using direct digital input, but if you are recording analog microphone or line signals via the "L-INPUT-R" jacks you will need to select the appropriate AD Input Gain setting. With the top function line highlighted, use Knob 3 to select "Line" if you will be recording line-level signals, or "Mic" if you will be recording a low-level microphone signal. 10. Set the Trigger Options The "REC-Trigger" display also offers "Start" and "Stop" trigger type and edge level parameters (function lines 3 and 4, respectively). If you want to start and stop recording manually (i.e. by pressing a panel button), select the "Manual" trigger mode. If you select the "Edge/Manual" mode, recording will be triggered automatically when the input signal level exceeds the threshold set by the corresponding "EdgeLevel" parameter (recording can still be triggered manually in this mode). The higher the edge level setting, the higher the signal level required to trigger recording. You can check your edge level setting visually in this page by applying the signal to be recorded to the A5000/A4000 and watching the meter and edge level marker at the top of the display. The same applies to "Stop" triggering. You can stop recording in the "Manual" mode, or select the "Edge/Manual" mode so that recording stops automatically when the source signal level drops below the threshold set by the "EdgeLevel" parameter. Level Input Signal Stop Edge Level Start Edge Level Start Recording Time Stop Recording • When the MONITOR function is turned off, the source signal is not routed to the sampler's outputs for monitoring. If you wish to monitor the source via the sampler's outputs while recording, press Knob 2 (MONITOR) to turn monitoring on (the "MONITOR D" icon will appear). 40 Chapter 2 Sampler Basics & Essential Procedures • A5000/A4000 q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q

Section	Page
Cover	1
List of Accessories	4
Features	5
Using the Manual	6
Manual Organization	6
Finding Information You Need	6
Other Conventions	7
Contents	8
Panel and Connector Arrangement	10
A5000/A4000 Options	14
Handling the Floppy Disk Drive(FDD) and Floppy Disk	15
Chapter 1 Setting Up	17
Setup Procedure	18
Power Connection	19
Audio Output Connections	20
Audio Input Connections	23
MIDI Connections	25
Powering On and Off	27
Sound Check	28
Chapter 2 Sampler Basics & Essential Procedures	31
SAMPLER BASICS	32
ESSENTIAL PROCEDURES	37
Chapter 3 The A5000/A4000 System & Features	57
1. System Overview	58
Internal Structure	58
Sampling Tone Generator	59
The Effect Stage	63
Total EQ	64
Controllers	64
Sequencer	64
I/O Interface	65
Data Organization & Management	65
2. The A5000/A4000 Functions	68
A5000/A4000 Mode Organization	68
Function Tree	73
3. Basic Operation	77
Common Mode Display Features	77
Selecting Modes & Functions	77
Selecting Display Pages	78
Editing Parameters	79
Executing Functions	80
Command Selection	80
Character Entry	81
MIDI Input	82
QUICK Entry	83
Tree View Display	83
A/D Input	85
MIDI Indicator	85
Shortcut Operation	86
Special Button Functions	86
Factory Reset	86
Chapter 4 PLAY Mode	87
About the PLAY Mode	88
1. PROGRAM	89
Program Select	89
Program Mix	90
Program Portamento	91
2. SAMPLE	93
Select Sample	93
Select Sample from Sample Bank	95
3. EASY EDIT	96
Mix	96
Output	97
Out & Gain	97
Filter	98
Pitch	98
Amplitude EG	99
Key	99
Velocity	100
Crossfade	100
Control	101
4. EFFECT	102
Effect Setup A	102
Effect Setup B	104
Effect Edit	104
5. SETUP	107
S/H Speed	107
AD Input	107
6. CONTROL	110
Program Controller A/B	110
Channel Setup	112
Program LFO	113
Chapter 5 EDIT Mode	117
About the EDIT Mode	118
1. TRIM/LOOP	120
Waveform	120
Sample Information	124
Loop Remix	125
2. MAP/OUT	127
Mix & Key Range	127
Pitch	129
Expand & Velocity Range	131
Level Scaling	132
3. FILTER	133
Filter & EQ	133
Filter Scaling	135
4. EG	137
Amplitude EG	137
Filter EG	138
Pitch EG	140
5. LFO	143
LFO	143
6. MIDI/CTRL	145
MIDI Set	145
Sample Controller A & B	146
Chapter 6 RECORD Mode	149
About the RECORD Mode	150
1. RECORD	151
Record	151
2. SETUP	153
Record Setup	153
Process	157
3. TRIGGER	158
Trigger	158
4. EFFECT	160
Recording Effect Setup	160
Recording Effect Edit	160
5. EXT CTRL (External Control)	161
CD-DA Control	161
6. MONITOR	163
Monitor & Click	163
Chapter 7 DISK Mode	165
About the DISK Mode	166
1. PROGRAM	167
PgmLoad	167
2. SAMPLE	169
SmpLoad	169
3. SEQUENCE	171
SeqLoad	171
4. VOLUME	172
Volume	172
5. DISK	173
Disk Select	173
Disk Setup	173
6. IMPORT	175
Import	175
7. DISK COMMANDS	177
Selecting a Command	177
Command Execution	177
SAVE	177
FORMAT	177
COPY VOLUME	181
SYSTEM FILE	182
BACKUP	182
CD-DA	184
LOAD OS	185
Chapter 8 UTILITY Mode	187
About the UTILITY Mode	188
1. TOTAL EQ	189
Total Equalizer	189
2. PANEL PLAY	191
Knob Controller	191
Knob Controller Setup	191
Function Key Play Setup	192
3. SEQUENCE	194
Sequence	194
4. MASTER	195
Tuning	195
Output	195
5. SYSTEM	197
KeysSet	197
Customise	198
6. MIDI	200
Channel Message	200
System Exclusive	201
Chapter 9 COMMAND	203
About the COMMANDS	204
Selecting a Command	206
Command Execution	206
COPY	206
DELETE	208
SAVE	208
ARRANGE	211
FREEZE	212
REGISTER	214
BULK DUMP	216
INITIALIZE	217
PROCESS	218
LOOP DIVIDE	221
RESAMPLE	222
STEREO -> MONO	225
MOVE	226
CREATE OSC	227
EXPORT	228
REVERT	230
Appendix	231
Installing Optional Equipment	232
Removing the Top Cover	232
Replacing the Top Cover	233
Installing SIMMs	234
Installing the AIEB1 I/O Expansion Board	237
Installing an Internal SCSI Hard Disk	240
Installing an Internal IDE Hard Disk	244
Installing an ATAPI ZIP Drive	247
Connecting external SCSI devices	251
Specifications	254
Effect Type List	256
Effect Parameter List	258
Control Change Number List	270
Troubleshooting	271
Error Messages	273
MIDI Data Format	274
A5000/A4000 MIDI Implementation Chart	286

Match case Limit results 1 per page

ESSENTIAL PROCEDURES

Chapter 2

Sampler Basics & Essential Procedures

• A5000/A4000

● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●

Go To the Record Trigger Display

Press the [TRIGGER] function key to go to the “REC-Trigger” display.

Set the AD Input Gain

This is not necessary if you’re using direct digital input, but if you are recording analog microphone or

line signals via the “L-INPUT-R” jacks you will need to select the appropriate AD Input Gain setting.

With the top function line highlighted, use Knob 3 to select “Line” if you will be recording line-level

signals, or “Mic” if you will be recording a low-level microphone signal.

10.

Set the Trigger Options

The “REC-Trigger” display also offers “Start” and “Stop” trigger type and edge level parameters

(function lines 3 and 4, respectively). If you want to start and stop recording manually (i.e. by pressing

a panel button), select the “Manual” trigger mode. If you select the “Edge/Manual” mode, recording

will be triggered automatically when the input signal level exceeds the threshold set by the corre-

sponding “EdgeLevel” parameter (recording can still be triggered manually in this mode). The higher

the edge level setting, the higher the signal level required to trigger recording. You can check your

edge level setting visually in this page by applying the signal to be recorded to the A5000/A4000 and

watching the meter and edge level marker at the top of the display.

The same applies to “Stop” triggering. You can stop recording in the “Manual” mode, or select the

“Edge/Manual” mode so that recording stops automatically when the source signal level drops

below

the threshold set by the “EdgeLevel” parameter.

•

When the MONITOR function is turned off, the source signal is not routed to the sampler's outputs

for monitoring. If you wish to monitor the source via the sampler's outputs while recording, press

Knob 2 (MONITOR) to turn monitoring on (the "MONITOR D" icon will appear).

Level

Input Signal

Stop Edge Level

Start Edge Level

Start Recording

Stop Recording

Time