Yamaha A5000 Owner's Manual - Page 169

DISK-SAMPLE 2. SAMPLE SAMPLE allows samples to be loaded into the sampler's memory from floppy disk, hard disk, or other media to which they have been saved. When a sample on a SCSI disk is selected, the sound of the sample can be directly monitored from disk by pressing the [AUDITION] button (this function may not work properly with some SCSI devices). Press the [DISK] button and then the [F2] button to go to the SAMPLE display. 1 display page is provided: SmpLoad (Sample Load). • The capacity of the wave memory may be exceeded when loading a number of voices. We recommend installing SIMM expansion memory to avoid this problem. SmpLoad [DISK] Button → [F2]Button → to select "DISK-SmpLoad" This function can be used to load a single sample or sample bank (including all the samples it contains), or all samples/ sample banks within a selected volume. Cursor q Cursor q Turn action Press action Knob 1 Cursor Tree View Knob 2 Disk - Knob 3 - DELETE Knob 4 Sample LOAD Knob 5 - LOAD ALL Knob 1 [ Turn] Cursor Positions the cursor. [ Press] Tree View Calls the Tree View display (page 83). Knob 3 [ Press] DELETE Deletes the selected sample from the disk. A confirmation display will appear when the knob is pressed. Press Knob 5 (>YES) to actually execute the delete operation. Knob 4 [ Turn] Sample Selects the sample or sample bank to be loaded. Samples cannot be selected if a non-native disk or a multi-segment floppy disk is selected. [Range] All samples and sample banks in the selected volume. [ Press] LOAD Initiates loading of the selected sample or sample bank. A confirmation display will appear when the knob is pressed. Press Knob 5 (>YES) to actually execute the load operation. If a sample with the same name as one being loaded exists in memory a display allowing you to choose how to handle the situation will appear (see page 170). • When a sample bank is loaded all samples contained in that sample bank are loaded. Knob 5 [ Press] LOAD ALL All samples and sample banks in the currently selected volume will be loaded. When the knob is pressed a confirmation display will appear. Press Knob 5 (>YES) to actually execute the load operation. If a sample with the same name as one being loaded exists in memory a display allowing you to choose how to handle the situation will appear (see page 170). Cursor w Cursor w Knob 2 [ Turn] Disk Selects the floppy disk, hard disk, or other storage media from which a sample or sample bank is to be loaded. When a disk is selected, all volumes it contains are listed below the disk name, and all samples and sample banks contained in the selected volume are listed on the right side of the display. When a hard disk, CD-ROM drive or similar storage device is selected, the SCSI ID number or IDE M/S (Master/Slave) status of the device is shown to the right of the disk name. [Range] All installed/connected disks. • If a connected SCSI or IDE device (hard disk, ZIP drive, etc.) cannot be selected, go to the disk select display (DISK-DISK-Disk) and check the mount/ unmount status and SCSI ID settings of the device (page 173). Turn action Press action Knob 1 Cursor Tree View Knob 2 Volume - Knob 3 - DELETE Knob 4 Sample LOAD Knob 5 - LOAD ALL Knob 1 Same function as Cursor q (page 169). Knob 2 [ Turn] Volume Selects the volume containing the sample to be loaded. [Range] All volumes on the selected disk. • When a volume is selected the program list is updated to show all the programs in the selected volume. 169 q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q A5000/A4000 • Chapter 7 DISK Mode