Yamaha A5000 Owner's Manual - Page 195
MASTER, Tuning, Output
View all Yamaha A5000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 195 highlights
UTILITY-MASTER 4. MASTER Use this function to adjust the system's output pitch, to adjust the level to the stereo outputs, and to set an assignable-output destination for the stereo output signal. Press the [UTILITY] button and then the [F4] button to go to the MASTER function. 2 display pages are provided: Tuning, and Output. Tuning [UTILITY] Button → [F4] Button → Knob 1 to select "UTIL-Tuning" Use this page to adjust the tuning (shift the pitch) of all system output. Output [UTILITY] Button → [F4] Button → Knob 1 to select "UTIL-Output" This function allows the signal appearing at the STEREO OUTPUT jacks to simultaneously be sent to the assignable outputs, and level offset can be individually applied for each output. • The setting that you make at this page takes precedence over the assignable-output settings within samples and programs. If you select AsgnOut2&3 at this page, for example, then AsgnOut2&3 will always produce the same signal as the stereo outputs. Cursor q Cursor q Turn action Press action Knob 1 Page Tree View Knob 2 Tuning Coarse QUICK... Knob 3 Tuning Fine QUICK... Knob 4 - - Knob 5 - - Knob 1 [ Turn] Page Selects display pages. [ Press] Tree View Calls the Tree View display (page 83). Knob 2 [ Turn] Tuning Coarse Turn the knob to adjust the tuning, in semitone increments. [Range] -127 - +127 [ Press] QUICK... Calls the quick entry menu (page 83). Knob 3 [ Turn] Tuning Fine Turn the knob to adjust the tuning in increments of 1.171875 cent. (Note: 100 cents = 1 semitone) [Range] -63 - +63 • The pitch of A (standard frequency = 440 Hz) as a result of Master Tuning is displayed in Hertz above the parameter's value. [ Press] QUICK... Calls the quick entry menu (page 83). Knob 1 Turn action Cursor/Page Press action Tree View Knob 2 - - Knob 3 - - Knob 4 Knob 5 Stereo Out To Assignable DIG&OPT Bit Out - - Knob 1 [ Turn] Cursor/Page Positions the cursor and selects display pages. [ Press] Tree View Calls the Tree View display (page 83). Knob 4 [ Turn] Stereo Out To Assignable Out You can select an assignable-output destination for the stereo output signal - so that the stereo-output jacks and the selected assignable-output connectors produce exactly the same signal. [Range] off, AsgnOutL&R, AsgnOut1&2 - AsgnOut5&6, DIG&OPT • off ... The stereo output signal is not simultaneously routed to any assignable output. • AsgnOutL&R ... The stereo output signal is simultaneously routed to the Assignable Out L & R outputs. • AsgnOut1&2 - AsgnOut5&6 ... The stereo output signal is simultaneously routed to the specified Assignable Outputs. • DIG&OPT ... The stereo output signal is simultaneously routed to the DIG&OPT (digital coaxial and optical) outputs. • The AsgnOut1&2, AsgnOut3&4, AsgnOut5&6, and DIG&OPT outputs cannot be selected unless the optional AIEB1 I/O expansion board is installed. 195 q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q A5000/A4000 • Chapter 8 UTILITY Mode