Yamaha A5000 Owner's Manual - Page 114

PLAY-CONTROL Knob 4 [ Turn] Program LFO Tempo Specifies the tempo on which the program LFO speed will be based. The actual LFO speed is determined by the setting of this parameter and the Program LFO Cycle parameter (when the Program LFO Sync parameter is set to "Manual"). [Range] 25 - 250 • This parameter cannot be edited when the Program LFO Sync parameter is set to MIDI-A or MIDI-B (MIDI on the A4000). [ Press] QUICK... Calls the quick entry menu (page 83). Knob 5 [ Turn] Program LFO Cycle Determines the LFO cycle in relation to the tempo set by the Program LFO Tempo parameter. [Range] e, q, e x 3, q x 2, q x 4, q x 8, q x 16 "e" produces the fastest LFO cycle (twice the Program LFO Tempo setting), while "q x 16" produces the slowest LFO cycle (1/16th the Program LFO Tempo setting). Cursor w Cursor w Turn action Press action Knob 1 Cursor/Page Tree View Knob 2 Knob 3 Program LFO Initial Phase Program LFO Phase Reset Ch - MIDI Knob 4 - - Knob 5 Program LFO Phase Reset Note MIDI Knob 1 Same function as Cursor q (page 113). Knob 2 [ Turn] Program LFO Initial Phase Specifies the phase angle at which the progam LFO cycle begins. [Range] 0°, 90°, 180°, 270° 0° 90° 180° 270° • The Program LFO Initial Phase setting becomes effective when a Program LFO Reset Channel command is received, or if the Program LFO Sync parameter is set to MIDI-A or MIDI-B (MIDI on the A4000). Knob 3 [ Turn] Program LFO Phase Reset Ch Specifies the MIDI channel on which phase reset note data (Program LFO Phase Reset Note) will be received. [Range] off, AUD, A01 - B16 (01 - 16 on the A4000), Bch • off ... No phase reset occurs even if note-on data is received. • AUD ... The LFO phase is reset when the panel [AUDITION] bnutton is pressed. • A01 - B16, Bch (basic receive channel) ... The phase will be reset when a Program LFO Reset Note is received on the specified channel. [ Press] MIDI Allows the Program LFO Phase Reset Channel to be set directly from an external MIDI device (page 82). • When setting the MIDI channel via MIDI on the A5000, receive the appropriate MIDI messages via the MIDI IN-A connector to set channels A01 - A16, and via the MIDI IN-B connector to set channels B01 - B16. Knob 5 [ Turn] Program LFO Phase Reset Note Specifies the note(s) which will be used to reset the phase of the Program LFO. [Range] all, C-2 - G8 • all ... The Program LFO phase will be set by any note received via the Program LFO Phase Reset channel. • C-2 - G8 ... The Program LFO phase will be set by notes in the specified range received via the Program LFO Phase Reset channel. • This parameter cannot be edited when Program LFO Sync is set to MIDI-A or MIDI-B (MIDI on the A4000). • This parameter cannot be edited when Program LFO Sync is set to Manual, or the Program Phase Rest Channel is set to off or AUD. [ Press] MIDI Allows the parameter to be set directly by receiving an appropriate MIDI message from an external MIDI device (page 82). 114 Chapter 4 PLAY Mode • A5000/A4000 q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q q