HP Photosmart C7100 Basics Guide - Page 63

slide does not touch the glass the final scanned image might be blurry.

Get HP Photosmart C7100 - All-in-One Printer PDF manuals and user guides View all HP Photosmart C7100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Chapter 4 1. Raise the lid and remove the Slide and Negative Film holder and the lid backing. Set the lid backing aside where it will not get damaged or dirty. 2. Unfold the holder so that the half with four slide openings is on top. 3. Place the holder on the glass and match the bottom edge with the bottom edge of the glass. Then, match the right tab on the top half of the holder with the right edge of the glass. 4. Place the slide on the holder so that the front of the image faces down and appears backward. Gently press down until it snaps into place. Note The slide must snap into place for the image to scan properly. If the slide does not touch the glass the final scanned image might be blurry. Tip If the slide does not snap into place easily, try rotating it 180 degrees. Some slides have a gap on one side that prevents them from fitting properly. Use the HP All-in-One features 5. Lower the lid of the HP All-in-One before starting the scan. 60 HP Photosmart C7100 All-in-One series

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
1.
Raise the lid and remove the Slide and Negative Film holder and the lid backing.
Set the lid backing aside where it will not get damaged or dirty.
2.
Unfold the holder so that the half with four slide openings is on top.
3.
Place the holder on the glass and match the bottom edge with the bottom edge of
the glass. Then, match the right tab on the top half of the holder with the right edge
of the glass.
4.
Place the slide on the holder so that the front of the image faces down and appears
backward. Gently press down until it snaps into place.
Note
The slide must snap into place for the image to scan properly. If the
slide does not touch the glass the final scanned image might be blurry.
Tip
If the slide does not snap into place easily, try rotating it 180 degrees.
Some slides have a gap on one side that prevents them from fitting properly.
5.
Lower the lid of the HP All-in-One before starting the scan.
Chapter 4
60
HP Photosmart C7100 All-in-One series
Use the HP All-in-One features