Netgear GS748Tv4 GS748Tv4 Software Administration Manual - Page 44

Server Type, Address, Priority, Version, Delete, Apply, Cancel, The entry is removed

Get Netgear GS748Tv4 PDF manuals and user guides View all Netgear GS748Tv4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

GS748T Smart Switch Software Administration Manual To configure a new SNTP Server: 1. Enter the appropriate SNTP server information in the available fields: • Server Type. Specifies whether the address for the SNTP server is an IP address (IPv4) or hostname (DNS). • Address. Enter the IP address or the hostname of the SNTP server. • Port. Enter a port number on the SNTP server to which SNTP requests are sent. The valid range is 1-65535. The default is 123. • Priority. Specifies the priority of this server entry in determining the sequence of servers to which SNTP requests are sent. Enter a priority from 1-3, with 1 being the default and the highest priority. Servers with lowest numbers have priority. • Version. Enter the protocol version number. The range is 1-4. 2. Click Add. 3. Repeat the previous steps to add additional SNTP servers. You can configure up to three SNTP servers. 4. To removing an SNTP server, select the check box next to the configured server to remove, and then click Delete. The entry is removed, and the device is updated. 5. To change the settings for an existing SNTP server, select the check box next to the configured server and enter new values in the available fields, and then click Apply. Configuration changes take effect immediately. 6. Click Cancel to cancel the configuration on the screen and reset the data on the screen to the latest value of the switch. 44 | Chapter 2: Configuring System Information

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
44
|
Chapter 2:
Configuring System Information
GS748T Smart Switch Software Administration Manual
To configure a new SNTP Server:
1.
Enter the appropriate SNTP server information in the available fields:
•
Server Type
. Specifies whether the address for the SNTP server is an IP address
(IPv4) or hostname (DNS).
•
Address
. Enter the IP address or the hostname of the SNTP server.
•
Port
. Enter a port number on the SNTP server to which SNTP requests are sent. The
valid range is 1–65535. The default is 123.
•
Priority
. Specifies the priority of this server entry in determining the sequence of
servers to which SNTP requests are sent. Enter a priority from 1–3, with 1 being the
default and the highest priority. Servers with lowest numbers have priority.
•
Version
. Enter the protocol version number. The range is 1–4.
2.
Click
Add
.
3.
Repeat the previous steps to add additional SNTP servers. You can configure up to three
SNTP servers.
4.
To removing an SNTP server, select the check box next to the configured server to remove,
and then click
Delete
. The entry is removed, and the device is updated.
5.
To change the settings for an existing SNTP server, select the check box next to the
configured server and enter new values in the available fields, and then click
Apply
.
Configuration changes take effect immediately.
6.
Click
Cancel
to cancel the configuration on the screen and reset the data on the screen to
the latest value of the switch.