Panasonic WJ-HD716/1000 Installation Guide - Page 72

Con the event action at a terminal alarm occurrence [Terminal, Command]

Get Panasonic WJ-HD716/1000 PDF manuals and user guides View all Panasonic WJ-HD716/1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Configure the event action at a terminal alarm occurrence [Terminal/ Command] Select the [Terminal/Command] tab on the "Event" page. (☞ Page 60) The settings relating to event actions to be taken at a terminal alarm (☞ Operating Instructions (PDF)) occurrence can be configured on this tab. [Operation mode] Select the settings for the operation mode. Refer to the operating instructions (PDF) for further information about the operation mode. ADM (Activity Detection Mode): Performs recording, writes the event log, and moves the cameras to preset positions at an event occurrence. Other event actions will not be performed. ALM (Alarm Mode): Performs every event action according to the settings. Off: Performs only writing an event log. Other event actions will no be performed. Configure the following settings for each Alarm Input (1 to 16) of the ALARM/CONTROL connector on the rear panel of the recorder. [Rec. cam.] Select a camera channel (1 to 16) used for recording. When "Off" is selected, recording will not be performed. [Preset] Select a preset position (1 to 256) to which the camera will move at an alarm occurrence. When the preset positions of two or more cameras have been selected on the advanced setup page is displayed and it is impossible to select the values. [Output terminal] Select a terminal (TRM1 to TRM16) to output the alarm signal. [Terminal setup] Select how to supply the signal to the alarm terminal. N.C.: Signals will be supplied when open-circuited. (Normally Close) N.O.: Signals will be supplied when short-circuited. (Normally Open) Default: N.C. 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
72
[Operation mode]
Select the settings for the operation mode.
Refer to the operating instructions (PDF) for further informa-
tion about the operation mode.
ADM (Activity Detection Mode):
Performs recording,
writes the event log, and moves the cameras to pre-
set positions at an event occurrence.
Other event actions will not be performed.
ALM (Alarm Mode):
Performs every event action
according to the settings.
Off:
Performs only writing an event log. Other event
actions will no be performed.
Configure the following settings for each Alarm Input (1 to
16) of the ALARM/CONTROL connector on the rear panel of
the recorder.
[Rec. cam.]
Select a camera channel (1 to 16) used for recording. When
"Off" is selected, recording will not be performed.
[Preset]
Select a preset position (1 to 256) to which the camera will
move at an alarm occurrence.
When the preset positions of two or more cameras have
been selected on the advanced setup page, "
∗∗∗
" is dis-
played and it is impossible to select the values.
[Output terminal]
Select a terminal (TRM1 to TRM16) to output the alarm sig-
nal.
[Terminal setup]
Select how to supply the signal to the alarm terminal.
N.C.:
Signals will be supplied when open-circuited.
(Normally Close)
N.O.:
Signals will be supplied when short-circuited.
(Normally Open)
Default:
N.C.
Configure the event action at a terminal alarm occurrence [Terminal/
Command]
Select the [Terminal/Command] tab on the "Event" page. (
+
Page 60)
The settings relating to event actions to be taken at a terminal alarm (
+
Operating Instructions (PDF)) occurrence can be config-
ured on this tab.