HP 6125G HP 6125G & 6125G/XG Blade Switches Network Management and Mon - Page 70

Configuration procedure, Con the SNMP NMS

Get HP 6125G PDF manuals and user guides View all HP 6125G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Figure 25 Network diagram Configuration procedure 1. Configure the agent: # Configure the IP address of the agent and make sure the agent and the NMS can reach each other. (Details not shown.) # Assign the NMS read and write access to the objects under the snmp node (OID 1.3.6.1.2.1.11), and deny its access to any other MIB object. system-view [Agent] undo snmp-agent mib-view ViewDefault [Agent] snmp-agent mib-view included test snmp [Agent] snmp-agent group v3 managev3group read-view test write-view test # Set the username to managev3user, authentication algorithm to MD5, authentication key to authkey, encryption algorithm to DES56, and privacy key to prikey. [Agent] snmp-agent usm-user v3 managev3user managev3group authentication-mode md5 authkey privacy-mode des56 prikey # Configure contact person and physical location information for the agent. [Agent] snmp-agent sys-info contact Mr.Wang-Tel:3306 [Agent] snmp-agent sys-info location telephone-closet,3rd-floor # Enable traps, specify the NMS at 1.1.1.2 as a trap destination, and set the username to managev3user for the traps. [Agent] snmp-agent trap enable [Agent] snmp-agent target-host trap address udp-domain 1.1.1.2 params securityname managev3user v3 privacy 2. Configure the SNMP NMS: { Specify the SNMP version for the NMS as v3. { Create two SNMP users: managev3user and public. { Enable both authentication and privacy functions. { Use MD5 for authentication and DES for encryption. { Set the authentication key to authkey and the privacy key to prikey. { Set the timeout time and maximum number of retries. For information about configuring the NMS, see the NMS manual. NOTE: The SNMP settings on the agent and the NMS must match. 3. Verify the configuration: # Try to get the count of sent traps from the agent. The get attempt succeeds. Send request to 1.1.1.1/161 ... Protocol version: SNMPv3 Operation: Get 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
63
Figure 25
Network diagram
Configuration procedure
1.
Configure the agent:
# Configure the IP address of the agent and make sure the agent and the NMS can reach each
other. (Details not shown.)
# Assign the NMS read and write access to the objects under the snmp node (OID
1.3.6.1.2.1.11), and deny its access to any other MIB object.
<Agent> system-view
[Agent] undo snmp-agent mib-view ViewDefault
[Agent] snmp-agent mib-view included test snmp
[Agent] snmp-agent group v3 managev3group read-view test write-view test
# Set the username to
managev3user
, authentication algorithm to
MD5
, authentication key to
authkey
, encryption algorithm to
DES56
, and privacy key to
prikey
.
[Agent] snmp-agent usm-user v3 managev3user managev3group authentication-mode md5
authkey privacy-mode des56 prikey
# Configure contact person and physical location information for the agent.
[Agent] snmp-agent sys-info contact Mr.Wang-Tel:3306
[Agent] snmp-agent sys-info location telephone-closet,3rd-floor
# Enable traps, specify the NMS at 1.1.1.2 as a trap destination, and set the username to
managev3user for the traps.
[Agent] snmp-agent trap enable
[Agent] snmp-agent target-host trap address udp-domain 1.1.1.2 params securityname
managev3user v3 privacy
2.
Configure the SNMP NMS:
{
Specify the SNMP version for the NMS as v3.
{
Create two SNMP users: managev3user and
public
.
{
Enable both authentication and privacy functions.
{
Use MD5 for authentication and DES for encryption.
{
Set the authentication key to
authkey
and the privacy key to
prikey
.
{
Set the timeout time and maximum number of retries.
For information about configuring the NMS, see the NMS manual.
NOTE:
The SNMP settings on the agent and the NMS must match.
3.
Verify the configuration:
# Try to get the count of sent traps from the agent. The get attempt succeeds.
Send request to 1.1.1.1/161 ...
Protocol version: SNMPv3
Operation: Get