HP DL360 HP ProLiant DL360 Generation 3 Server Setup and Installation Guide - Page 28

Replacing an Expansion Board

Get HP DL360 - ProLiant - G3 PDF manuals and user guides
UPC - 613326948835
View all HP DL360 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Installing Hardware Options Replacing an Expansion Board To install an expansion board, complete the procedures described in the following subsections. Removing an Expansion Board The expansion board and PCI riser board assembly must be removed to replace an expansion board. CAUTION: To avoid damaging the system or expansion boards, remove all AC power cords before installing or removing an expansion board. When the front panel power switch is in the Off position, auxiliary power is still connected to the PCI expansion slot and may damage the card. 1. Access internal server components. Refer to the "Accessing Internal Server Components" section earlier in this chapter. 2. Disconnect any cables leading from any existing expansion board in the system board. HP ProLiant DL360 Generation 3 Server Setup and Installation Guide 2-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Installing Hardware Options
HP ProLiant DL360 Generation 3 Server Setup and Installation Guide
2-9
Replacing an Expansion Board
To install an expansion board, complete the procedures described in the following
subsections.
Removing an Expansion Board
The expansion board and PCI riser board assembly must be removed to replace an
expansion board.
CAUTION:
To avoid damaging the system or expansion boards, remove all AC
power cords before installing or removing an expansion board. When the front panel
power switch is in the Off position, auxiliary power is still connected to the PCI
expansion slot and may damage the card.
1.
Access internal server components. Refer to the “Accessing Internal Server
Components” section earlier in this chapter.
2.
Disconnect any cables leading from any existing expansion board in the system
board.