HP DL360 HP ProLiant DL360 Generation 3 Server Setup and Installation Guide - Page 59

Precon d Operating System

Get HP DL360 - ProLiant - G3 PDF manuals and user guides
UPC - 613326948835
View all HP DL360 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Server Installation 4. Install the operating system. 5. Install Insight Manager to manage the server. For Management CD initialization procedures, refer to the Server Setup and Management pack that shipped with the server. IMPORTANT: Insight Manager must be installed to benefit from Prefailure Warranties on processors, hard drives, and memory modules. 6. Install any application software needed. 7. Register the server. Refer to "Registering the Server" later in this chapter. Preconfigured Operating System WARNING: To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding plug. The grounding plug is an important safety feature. • Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. • Disconnect power from the server by unplugging the power cord from either the electrical outlet or the server. • Do not place anything on power cords or cables. Arrange them so that no one can accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging the cord from the electrical outlet, grasp the cord by the plug. CAUTION: Use the SmartStart CD as recovery software only. Powering up the server from the SmartStart CD reconfigures the system and causes all data on the server to be lost. If the server was ordered with the operating system factory installed, everything required to install the operating system is already on the server. Refer to the steps provided in the HP Factory-Installed Operating System Software User Guide for more information on using the operating system. To complete the installation process with a preconfigured operating system: 1. Power up the server. Refer to "Powering Up the Server" earlier in this chapter. 3-14 HP ProLiant DL360 Generation 3 Server Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Server Installation
3-14
HP ProLiant DL360 Generation 3 Server Setup and Installation Guide
4.
Install the operating system.
5.
Install Insight Manager to manage the server. For Management CD initialization
procedures, refer to the Server Setup and Management pack that shipped with the
server.
IMPORTANT:
Insight Manager must be installed to benefit from Prefailure Warranties on
processors, hard drives, and memory modules.
6.
Install any application software needed.
7.
Register the server. Refer to “Registering the Server” later in this chapter.
Preconfigured Operating System
WARNING:
To reduce the risk of electric shock or damage to the equipment:
•
Do not disable the power cord grounding plug. The grounding plug is an
important safety feature.
•
Plug the power cord into a grounded (earthed) electrical outlet that is
easily accessible at all times.
•
Disconnect power from the server by unplugging the power cord from
either the electrical outlet or the server.
•
Do not place anything on power cords or cables. Arrange them so that no
one can accidentally step on or trip over them. Do not pull on a cord or
cable. When unplugging the cord from the electrical outlet, grasp the cord
by the plug.
CAUTION:
Use the SmartStart CD as recovery software only. Powering up the
server from the SmartStart CD reconfigures the system and causes all data on the
server to be lost.
If the server was ordered with the operating system factory installed, everything
required to install the operating system is already on the server. Refer to the steps
provided in the
HP Factory-Installed Operating System Software User Guide
for
more information on using the operating system.
To complete the installation process with a preconfigured operating system:
1.
Power up the server. Refer to “Powering Up the Server” earlier in this chapter.