Home » HP Manuals » Desktops » HP Dc7100 » Manual Viewer

HP Dc7100 HP Compaq Business Desktop dc7100 Series Service Reference Guide, 3r - Page 75

Operating Guidelines, 5.4 Routine Care, 5.4.1 General Cleaning Safety Precautions

UPC - 829160356877

Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Identifying the Chassis, Routine Care, and Disassembly Preparation ■ Static awareness labels ■ Wrist straps and footwear straps providing one-megohm +/- 10% resistance ■ Material handling packages ■ Conductive plastic bags ■ Conductive plastic tubes ■ Conductive tote boxes ■ Opaque shielding bags ■ Transparent metallized shielding bags ■ Transparent shielding tubes 5.3 Operating Guidelines To prevent overheating and to help prolong the life of the computer: ■ Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold. ■ Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance on all vented sides of the computer and above the monitor to permit the required airflow. ■ Never restrict the airflow into the computer by blocking any vents or air intakes. Do not place the keyboard, with the keyboard feet down, directly against the front of the desktop unit as this also restricts airflow. ■ Occasionally clean the air vents on all vented sides of the computer. Lint, dust, and other foreign matter can block the vents and limit the airflow. ■ Never operate the computer with the cover or side panel removed. ■ Do not stack computers on top of each other or place computers so near each other that they are subject to each other's re-circulated or preheated air. ■ If the computer is to be operated within a separate enclosure, intake and exhaust ventilation must be provided on the enclosure, and the same operating guidelines listed above will still apply. ■ The computer is designed to operate continuously (24x7), provided that the operating guidelines listed above are met. ■ Install or enable power management functions of the operating system or other software, including sleep states. 5.4 Routine Care 5.4.1 General Cleaning Safety Precautions 1. Never use solvents or flammable solutions to clean the computer. 2. Never immerse any parts in water or cleaning solutions; apply any liquids to a clean cloth and then use the cloth on the component. 3. Always unplug the computer when cleaning with liquids or damp cloths. 4. Always unplug the computer before cleaning the keyboard, mouse, or air vents. Service Reference Guide, dc7100 361288-003 5-5

Section	Page
1	9
1.1 Installing or Upgrading Device Drivers	9
1.2 Transferring Files and Settings	10
1.3 Backing Up and Restoring Files	10
1.3.1 Creating a Backup File-Windows XP Professional	10
1.3.2 Restoring from the Backup File-Windows XP Professional	10
1.4 Converting to NTFS	10
1.5 HP Software	10
2	13
2.1 Power-On Self-Test (POST)	13
2.2 Computer Setup Utilities	14
2.2.1 Using Computer Setup (F10) Utilities	15
2.2.2 Computer Setup Menu	16
2.3 Diagnostics for Windows	26
2.3.1 Detecting Diagnostics for Windows	27
2.3.2 Installing Diagnostics for Windows	27
2.3.3 Using Categories in Diagnostics for Windows	28
2.3.4 Running Diagnostic Tests in Diagnostics for Windows	29
2.4 Configuration Record	30
2.4.1 Installing Configuration Record	31
2.4.2 Running Configuration Record	31
3	33
3.1 Initial Configuration and Deployment	33
3.2 Remote System Installation	34
3.3 Software Updating and Management	34
3.3.1 HP Client Manager Software	34
3.3.2 Altiris Client Management Solutions	35
3.3.3 System Software Manager	35
3.3.4 Proactive Change Notification (PCN)	36
3.3.5 Subscriber’s Choice	36
3.3.6 ROM Flash	36
3.3.7 Remote ROM Flash	36
3.3.8 HPQFlash	37
3.3.9 FailSafe Boot Block ROM	37
3.3.10 Replicating the Setup	38
3.3.11 Dual-State Power Button	44
3.3.12 World Wide Web Site	44
3.3.13 Building Blocks and Partners	44
3.4 Asset Tracking and Security	45
3.4.1 Password Security	49
3.4.2 Establishing a Setup Password Using Computer Setup	49
3.4.3 Establishing a Power-On Password Using Computer Setup	49
3.4.4 DriveLock	52
3.4.5 Smart Cover Sensor	54
3.4.6 Master Boot Record Security	56
3.4.7 Before You Partition or Format the Current Bootable Disk	57
3.4.8 Cable Lock Provision	57
3.4.9 Fingerprint Identification Technology	57
3.5 Fault Notification and Recovery	58
3.5.1 Drive Protection System	58
3.5.2 Surge-Tolerant Power Supply	58
3.5.3 Thermal Sensor	58
4	59
4.1 SATA and PATA Device Information	59
4.2 ATA Cables	60
4.2.1 SATA Data Cable	60
4.2.2 SATA Power Cable	60
4.2.3 PATA Data Cable	61
4.2.4 PATA Power Cable	61
4.2.5 PATA Cable Layout	62
4.3 PATA Drive Installation Guidelines	63
4.3.1 PATA Device Classes	63
4.3.2 PATA Attach Sequence Rules by Class Priority	64
4.3.3 PATA Attach Sequence Worksheet	65
4.3.4 PATA Additional Drive Application Notes	67
4.4 ATA SMART Drives	68
4.5 Drive Capacities	68
4.6 SATA BIOS	69
4.6.1 Legacy Mode	69
4.6.2 Native Mode	69
4.7 Mixed Devices Boot and Drive Letter Ordering	70
5	71
5.1 Chassis Designations	71
5.1.1 Convertible Minitower (CMT)	71
5.1.2 Small Form Factor (SFF)	72
5.1.3 Ultra-Slim Desktop (USDT)	72
5.2 Electrostatic Discharge Information	73
5.2.1 Generating Static	73
5.2.2 Preventing Electrostatic Damage to Equipment	73
5.2.3 Personal Grounding Methods and Equipment	74
5.2.4 Grounding the Work Area	74
5.2.5 Recommended Materials and Equipment	74
5.3 Operating Guidelines	75
5.4 Routine Care	75
5.4.1 General Cleaning Safety Precautions	75
5.4.2 Cleaning the Computer Case	76
5.4.3 Cleaning the Keyboard	77
5.4.4 Cleaning the Monitor	77
5.4.5 Cleaning the Mouse	77
5.5 Service Considerations	78
5.5.1 Power Supply Fan	78
5.5.2 Tools and Software Requirements	78
5.5.3 Screws	78
5.5.4 Cables and Connectors	79
5.5.5 Hard Drives	79
5.5.6 Lithium Coin Cell Battery	79
6	81
6.1 Preparation for Disassembly	81
6.2 Unlocking the Smart Cover Lock	82
6.3 Hood Sensor	83
6.4 External Security Devices	84
6.4.1 Cable Lock	84
6.4.2 Padlock	85
6.5 Computer Access Panel	86
6.6 Front Bezel	87
6.7 Front Drive Bezels	88
6.7.1 5.25” Drive Bezel Blank	88
6.7.2 Diskette Drive Bezel or Bezel Blank	89
6.8 Cable Management	90
6.9 Memory	91
6.10 Expansion Cards	93
6.11 PCI Retainer Latch	97
6.12 Expansion Card Guide	99
6.13 Drives	100
6.13.1 Drive Positions	100
6.13.2 Hard Drive	101
6.13.3 Optical Drive	104
6.13.4 Diskette Drive	107
6.14 Front I/O Device	108
6.15 Power Switch Assembly	109
6.16 System Board	110
6.17 Battery	111
6.17.1 Type 1 Battery Holder	112
6.17.2 Type 2 Battery Holder	113
6.18 Heatsink	114
6.19 Processor	115
6.20 Speaker	117
6.21 Chassis Fan	118
6.22 Power Supply	119
6.23 Changing from Desktop to Minitower	120
6.24 Changing from Minitower to Desktop	123
Removal and Replacement Procedures- Small Form Factor (SFF) Chassis	127
7.1 Preparation for Disassembly	127
7.2 Unlocking the Smart Cover Lock	128
7.3 Hood Sensor	130
7.4 External Security Devices	131
7.4.1 Security Clip	131
7.4.2 Cable Lock	131
7.4.3 Padlock	132
7.4.4 Universal Chassis Clamp Lock	132
7.5 Computer Cover	137
7.6 Front Drive Bezels	138
7.7 Cable Management	140
7.8 Memory	142
7.9 Vertically Oriented Expansion Card	144
7.9.1 Expansion Card Retainer	144
7.9.2 PCI Expansion Card	145
7.9.3 PCI Express Expansion Card	147
7.10 Horizontally Oriented Expansion Card	148
7.10.1 Expansion Card Cage	148
7.10.2 PCI Expansion Card	148
7.10.3 Riser Card	151
7.11 Drives	152
7.11.1 Drive Positions	152
7.11.2 Optical Drive	153
7.11.3 External 3.5-inch Drive	155
7.11.4 Primary Hard Drive	156
7.12 Fan Shroud	160
7.13 Front I/O Devices	161
7.14 Power Switch Assembly	165
7.15 Heatsink	166
7.16 Processor	167
7.17 Speaker	169
7.18 Power Supply	170
7.19 System Board	172
7.20 Chassis Fan	176
7.21 Backwall	177
7.22 Battery	184
7.22.1 Type 1 Battery Holder	185
7.22.2 Type 2 Battery Holder	186
7.22.3 Type 3 Battery Holder	187
8	189
8.1 Preparation for Disassembly	189
8.2 External Security Devices	191
8.2.1 Installing a Cable Lock	191
8.2.2 Installing a Padlock	192
8.3 Computer Access Panel	193
8.4 MultiBay Device	194
8.5 MultiBay Riser Card	195
8.6 Front Panel Assembly	196
8.7 Front Bezel	197
8.8 Chassis Fan	198
8.9 Cable Management	199
8.10 Memory	200
8.11 Expansion Card Cage	202
8.12 Expansion Card	203
8.13 Hood Sensor	205
8.14 Expansion Card Retaining Latch	206
8.15 Hard Drive	207
8.16 Front I/O Device	209
8.17 Heatsink Assembly	210
8.17.1 Heatsink Fan with Shroud	211
8.18 Processor	212
8.19 Power Supply	214
8.20 Battery	215
8.20.1 Type 1 Battery Holder	216
8.20.2 Type 2 Battery Holder	217
8.20.3 Type 3 Battery	218
8.21 Speaker	219
8.22 System Board	220
A	221
B	231
C	233
D	243
E	277

Match case Limit results 1 per page

Service Reference Guide, dc7100

361288-003

5–5

Identifying the Chassis, Routine Care, and Disassembly Preparation

Static awareness labels

Wrist straps and footwear straps providing one-megohm +/- 10% resistance

Material handling packages

Conductive plastic bags

Conductive plastic tubes

Conductive tote boxes

Opaque shielding bags

Transparent metallized shielding bags

Transparent shielding tubes

5.3 Operating Guidelines

To prevent overheating and to help prolong the life of the computer:

Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and

cold.

Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance on all

vented sides of the computer and above the monitor to permit the required airflow.

Never restrict the airflow into the computer by blocking any vents or air intakes. Do not place

the keyboard, with the keyboard feet down, directly against the front of the desktop unit as

this also restricts airflow.

Occasionally clean the air vents on all vented sides of the computer. Lint, dust, and other

foreign matter can block the vents and limit the airflow.

Never operate the computer with the cover or side panel removed.

Do not stack computers on top of each other or place computers so near each other that they

are subject to each other’s re-circulated or preheated air.

If the computer is to be operated within a separate enclosure, intake and exhaust ventilation

must be provided on the enclosure, and the same operating guidelines listed above will still

apply.

The computer is designed to operate continuously (24x7), provided that the operating

guidelines listed above are met.

Install or enable power management functions of the operating system or other software,

including sleep states.

5.4 Routine Care

5.4.1 General Cleaning Safety Precautions

1. Never use solvents or flammable solutions to clean the computer.

2. Never immerse any parts in water or cleaning solutions; apply any liquids to a clean cloth

and then use the cloth on the component.

3. Always unplug the computer when cleaning with liquids or damp cloths.

4. Always unplug the computer before cleaning the keyboard, mouse, or air vents.