Sharp MX-M363N Installation Manual - Page 111

Check C., front side of then RSPF bottom is in contact with the glass

Get Sharp MX-M363N PDF manuals and user guides View all Sharp MX-M363N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

1 : '10/Jun/18 1 Check section B. Is there a re- No sistance? Yes d) Check section B. Place the RSPF height adjustment sheet between section B and the RSPF glass height adjustment resin surface (a), and close the RSPF unit. Slowly pull out the RSPF height adjustment sheet. Check to insure that a slight resistance is felt when pulling out the RSPF height adjustment sheet. (If the boss in section B is in contact, it is O.K.) * Be careful not to put the book sensor (b) on the height adjustment sheet. B b a e) If it can be pulled out without resistance, turn the hinge in section E clockwise to adjust. E Check section C. Is there No a separating section. Yes Adjust hinge E until the separation in section C is deleted. (Counterclockwise) * The bosses in section A and B are excessively pressed. (The right side is separating.) End of the adjustment f) Check section C. Check to confirm that the projection in section C in the right front side of then RSPF bottom is in contact with the glass surface (b). b C C b MX-M503N MX-RP11 28 - 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
MX-M503N
MX-RP11
28 – 5
Yes
Yes
No
No
End of the
adjustment
The bosses in section A
and B are excessively
pressed. (The right
side is separating.)
Adjust hinge
E until the
separation in
section C is
deleted.
(Counter-
clockwise)
Is
there a re-
sistance?
Is there
a separating
section.
Check section C.
e) If it can be pulled out without resistance, turn the hinge in
section E clockwise to adjust.
f)
Check section C.
Check to confirm that the projection in section C in the right
front side of then RSPF bottom is in contact with the glass
surface (b).
*
d) Check section B.
*
Check to insure that a slight resistance is felt when pulling out
the RSPF height adjustment sheet. (If the boss in section B is
in contact, it is O.K.)
Slowly pull out the RSPF height adjustment sheet.
Place the RSPF height adjustment sheet between section B
and the RSPF glass height adjustment resin surface (a), and
close the RSPF unit.
Be careful not to put the book sensor (b) on the height
adjustment sheet.
Check section B.
a
B
b
b
C
b
C
E
1
: '10/Jun/18
1