Sharp MX-M363N Installation Manual - Page 27

G. Size setting, H. Off-center adjustment, Adjustment with the simulation, Mechanical adjustment

Get Sharp MX-M363N PDF manuals and user guides View all Sharp MX-M363N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

2) Open the front cabinet. Turn ON the power switch in the front cabinet of the main unit. ON 4) Select a paper feed tray to be adjusted. ǂ7(ǂ6ǂ7 6,08/$7,21ǂǂ12 $872,0$*(326,7,21$'-8670(176(59,&( 0)7 &6 &6 &6 &6 /&&  &/26( $'8 3) Turn ON the power switch on the operation panel. G. Size setting Execute SIM 26-2 "Size setting" with the key operations of the main unit. 1) The size selection menu of the large capacity tray is displayed on the operation message display. 2) Select a size button to be set on the message screen. H. Off-center adjustment (1) Adjustment with the simulation Since the off-center adjustment is performed when shipping, there is basically no need to perform this adjustment. If the center is shifted, perform the following adjustment procedures. 1) Enter the SIM50-28 mode. ǂ7(ǂ6ǂ7 6,08/$7,21ǂǂ12 $872,0$*(326,7,21$'-8670(176(59,&( 2&ǂ$'63)ǂ$'- 5(68/7 %.0$*ǂ$'6(78335,17ǂ$'- '$7$  &/26( 2) Select [SETUP/PRINT] ADJ with the key button. 3) Select [ALL] with the key button. ǂ7(ǂ6ǂ7 6,08/$7,21ǂǂ12 $872,0$*(326,7,21$'-8670(176(59,&( /($' $// 2))6(7   &/26( (;(&87(  5) Press [EXECUTE] key. The adjustment pattern is printed out. 6) Set the adjustment pattern on the document table. (Any direction) NOTE: Fit the adjustment pattern correctly with the document guide. 7) Press [EXECUTE] key. The following item is automatically adjustment. * Print image lead edge image position adjustment * Print image off-center adjustment 8) Press [OK] key. The adjustment result becomes valid. Perform procedures 4) to 7) for each paper feed tray. (2) Mechanical adjustment Since the off-center adjustment is performed when shipping, there is basically no need to perform this adjustment. If the center is shifted, however, the simulation is normally used. If the shift is not removed, perform the following adjustment procedures. 1) Slowly pull out the tray until it stops.  (Note) By pressing [LEAD] or [OFFSET] button, the following items can be executed individually. * [LEAD]: Print image lead edge image position adjustment * [OFFSET]: Print image off-center adjustment When [ALL] is selected, both of the above two items are executed simultaneously. MX-M503N MX-LCX1 3 - 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
MX-M503N
MX-LCX1
3 – 8
2)
Open the front cabinet.
Turn ON the power switch in the front cabinet of the main unit.
3)
Turn ON the power switch on the operation panel.
G.
Size setting
Execute SIM 26-2 "Size setting" with the key operations of the main
unit.
1)
The size selection menu of the large capacity tray is displayed
on the operation message display.
2)
Select a size button to be set on the message screen.
H.
Off-center adjustment
(1)
Adjustment with the simulation
Since the off-center adjustment is performed when shipping, there
is basically no need to perform this adjustment. If the center is
shifted, perform the following adjustment procedures.
1)
Enter the SIM50-28 mode.
2)
Select [SETUP/PRINT] ADJ with the key button.
3)
Select [ALL] with the key button.
(Note)
By pressing [LEAD] or [OFFSET] button, the following items
can be executed individually.
*
[LEAD]: Print image lead edge image position adjustment
*
[OFFSET]: Print image off-center adjustment
When [ALL] is selected, both of the above two items are
executed simultaneously.
4)
Select a paper feed tray to be adjusted.
5)
Press [EXECUTE] key.
The adjustment pattern is printed out.
6)
Set the adjustment pattern on the document table. (Any direc-
tion)
NOTE:
Fit the adjustment pattern correctly with the document
guide.
7)
Press [EXECUTE] key.
The following item is automatically adjustment.
*
Print image lead edge image position adjustment
*
Print image off-center adjustment
8)
Press [OK] key.
The adjustment result becomes valid.
Perform procedures 4) to 7) for each paper feed tray.
(2)
Mechanical adjustment
Since the off-center adjustment is performed when shipping, there
is basically no need to perform this adjustment. If the center is
shifted, however, the simulation is normally used. If the shift is not
removed, perform the following adjustment procedures.
1)
Slowly pull out the tray until it stops.
ON