Home » Sharp Manuals » Multifunction Devices » Sharp MX-M363N » Manual Viewer

Sharp MX-M363N Installation Manual - Page 60

MX-PNX6A/B/C/D, 1. Unpacking, A. Pulling out of the punch unit, B. Removal of the protection

Get Sharp MX-M363N PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

[M1X-0M]50M3NX-PNX6A/B/C/D 1. Unpacking A. Pulling out of the punch unit 1) Pull out the punch unit. S2)erOvpiecnetheMfraonntucaovler, and open the top cover. 2 1 3) Remove the screws, and remove the fixing material. (2 posi- tions) B. Removal of the protection material 1) Remove the fixing tape and protection material. 4) Close the top cover, and close the front cover. 2 1 MX-M503N MX-PNX6A/B/C/D 10 - 1

Section	Page
CONFIGURATION	3
1. Main unit and option	3
2. Main unit configuration	4
3. Combination of options	4
MX-M283N/M363N/M363U/ M453N/M453U/M503N/M503U/ M282N/M362N/M452N/M502N	6
1. Installing (use) conditions	6
A. Bringing space	6
B. Installing space	6
C. Power source (Capacity, voltage, frequency, safety, plug)	6
D. Floor strength and level	6
E. Direct rays of the sun, dust, temperature, humidity, gasses, chemicals, vibration	6
F. Note for handling PWB and electronic parts	7
G. Note for handling the drum unit, the transfer unit, the developing unit, and the fusing unit	8
2. Transit and delivery	8
A. Implements, facility, and manpower	8
B. Delivery	8
3. Unpacking	8
A. Unpacking procedure	8
B. Removal of the fixing tape, protection material and parts packed together	8
C. Check the parts packed together	9
4. Installation	9
A. Lock release	9
B. Developer supply	10
C. Toner density reference control level setting	11
D. Install toner cartridge	11
E. Installation of the paper holding plate unit	11
F. Installation of the operation manual pocket	12
G. Tray setup	12
H. Specifications setup	13
I. Image quality check	13
J. Function and operation check	14
K. Setup and adjustment data recording	14
L. Necessary works before moving the machine	14
M. Remote operation panel function Enable setting	14
N. USB PORT selection	14
MX-DEX8/DEX9	15
1. Unpacking	15
A. Removal of the desk unit	15
B. Removal of the fixing material and packing parts	15
C. Check the packed items	15
2. Installation	15
A. Turn off the power of the main unit	15
B. Installation of the adjuster	16
C. Connection of the main unit and the desk unit	16
D. Release the lock	18
E. Connector connection	18
F. Turn on the power of the main unit	19
G. Image off-center adjustment	19
MX-LCX1	20
1. Unpacking	20
A. Removal of the large capacity tray unit	20
B. Removal of the fixing material and packing parts	20
C. Check the packed items	20
2. Installation	20
A. Turn off the power of the main unit	20
B. Connection of the main unit and the large capacity tray unit	21
C. Height adjustment of the large capacity tray unit	22
D. Connector connection	23
E. Paper size switch	23
F. Turn on the power of the main unit	26
G. Size setting	27
H. Off-center adjustment	27
MX-FNX9	29
1. Unpacking	29
A. Removal of the inner finisher	29
B. Removal of the fixing tape and protection material	29
C. Check the packed items	29
2. Installation	30
A. Turn off the power of the main unit	30
B. Removal of the paper holding plate unit	30
C. Installation of the inner finisher	30
D. Connector Installation	32
E. Staple position label attachment	33
F. Turn on the power of the main unit	33
MX-PNX1	34
1. Unpacking	34
A. Removal of the punch unit	34
B. Removal of the fixing tape	34
C. Check the packed items	34
2. Installation	34
A. Turn off the power of the main unit	34
B. Installation of the punch unit	35
C. Punch position label attachment	37
D. Turn on the power of the main unit	37
MX-RBX3	38
1. Unpacking	38
A. Removal of the interface pass unit	38
B. Removal of the fixing tape	38
C. Check the packed items	38
2. Installation	38
A. Turn off the power of the main unit	38
B. Removal of the paper holding plate unit	39
C. Installation of the interface pass unit	39
MX-FN10	41
1. Unpacking	41
A. Removal of the saddle finisher	41
B. Removal of the fixing tape and protection material	42
C. Check the packed items	42
2. Installation	42
A. Replacement of the Operation Manual storage cover	42
B. Installation of the paper exit tray	42
C. Staple cartridge installation	43
D. Height adjustment of the finisher	43
E. Connection of the main unit and saddle finisher	44
F. Connector connection	44
G. Staple position label attachment	45
H. Turn on the power of the main unit	45
MX-PNX5A/B/C/D	46
1. Unpacking	46
A. Removal of the punch unit	46
B. Check the packed items	46
2. Installation	46
A. Turn off the power of the main unit	46
B. Installation of the punch unit	46
C. Punch jam processing label attachment	48
D. Punch position label attachment	48
E. Turn on the power of the main unit	49
MX-FN11	50
1. Unpacking	50
A. Removal of the finisher	50
B. Removal of the protection material	51
C. Check the packed items	51
2. Installation	52
A. Replacement of the Operation Manual storage cover	52
B. Installation of the rail	52
C. Removal of the paper pass latch reception parts and the positioning pin	52
D. Attaching the mylar	53
E. Installation of the connection fixture F/R	53
F. Attaching the cushion	54
G. Check of the connected position of main unit and finisher	54
H. Adjustment	54
I. Connection of the finisher	58
J. Connection of connector to the main unit	59
K. Staple position label attachment	59
L. Turn ON the main power switch of the main unit	59
MX-PNX6A/B/C/D	60
1. Unpacking	60
A. Pulling out of the punch unit	60
B. Removal of the protection material	60
C. Check the packed items	61
2. Installation	61
A. Installation of punch unit	61
B. Connection of connector of the finisher and punch unit	62
C. Install of the Connection fixture F/R	62
D. Check of the connected position of main unit and finisher	62
E. Adjustment	63
F. Install to main unit	63
G. Connection of connector to the main unit	64
H. Punch position label attachment	64
I. Turn ON the main power switch of the main unit	65
MX-TRX2	66
1. Unpacking	66
A. Removal of the exit tray unit	66
B. Check the packed items	66
2. Installation	66
A. Turn off the power of the main unit	66
B. Installation of the exit roller unit	66
C. Turn on the power of the main unit.	67
D. Tray setting	67
MX-FXX2	68
1. Unpacking	68
A. Parts included	68
2. Installation	68
A. Turn off the power switches of the main unit.	68
B. Attach the fax box unit to the rear part of the main unit.	68
C. Pull out the control PWB.	68
D. Attach the FAX memory.	69
E. Attach the interface cable.	69
F. Attach the control PWB and the right cabinet rear.	69
G. Turn on the main power switch of the main unit.	70
H. Set the destination and the logo type.	70
I. Clear the FAX related software switches.	70
J. Clear the image memory.	71
K. Connect the line cable to the fax box unit.	71
L. Installation completion check	71
AR-SU1	72
1. Unpacking	72
A. Remove the stamp unit	72
B. Check the parts in the package	72
2. Installation	72
A. Turn off the power of the main unit	72
B. Install the stamp unit	72
C. Turn on the power of the main unit	74
MX-PB10	75
1. Unpacking	75
A. Parts included	75
2. Installation	75
A. Preparation for enabling the MX-PB10	75
MX-PB11	76
1. Unpacking	76
A. Parts included	76
2. Installation	76
A. Preliminary arrangements	76
B. Turn off the power of the main unit	76
C. Pull out the control PWB	77
D. HDD installation	77
E. Reattach the control PWB and the right cabinet rear	77
F. Turn ON the power of the main unit	78
G. Preparation for enabling the MX-PB11	78
H. User data restoring procedures	78
I. Deletion of backup data	78
MX-FWX1	79
1. Unpacking	79
A. Check the packed items	79
2. Installation	79
A. Preparation for enabling the Internet Fax send function	79
B. Operation check of the Internet Fax send function	79
MX-EBX3	80
1. Unpacking	80
A. Old type	80
B. Type A	80
C. Type B/Type C	80
2. Installation	81
A. Turn off the power of the main unit	81
B. Pull out the control PWB	81
C. Installation of the scanner function expansion PWB	81
D. Reattach the control PWB and the right cabinet rear	82
E. Turn ON the power of the main unit	82
MX-PKX1	84
1. Unpacking	84
A. Parts included	84
2. Installation	84
A. Preparation for enabling PS3	84
B. PS3 check	84
MX-PUX1	85
1. Unpacking	85
A. Check the packed items	85
2. Installation	85
A. Preparation for enabling XPS	85
MX-SMX3	86
1. Unpacking	86
A. Parts included	86
2. Installation	86
A. Turn off the power switches of the main unit.	86
B. Pull out the control PWB.	86
C. Installation of the expansion memory	86
D. Reattach the control PWB and the right cabinet rear.	87
E. Turn on the main power switch of the main unit.	87
AR-PF1	89
1. Unpacking	89
A. Parts included	89
2. Installation	89
A. Turn off the power switches of the main unit.	89
B. Pull out the control PWB.	89
C. Installation of the barcode font ROM PWB	89
D. Reattach the control PWB and the right cabinet rear.	90
E. Turn on the main power switch of the main unit.	90
F. PCL expansion font list check	90
G. Font list	90
MX-FR14U/FR14/FR15U/FR15/ FR24U	91
1. Unpacking	91
A. Check the packed items	91
2. Installation	91
A. Turn off the power switches of the main unit.	91
B. Pull out the control PWB.	91
C. Mount the data security kit ROMs to the control PWB unit.	92
D. Reattach the control PWB and the right cabinet rear.	92
E. Turn on the main power switch of the main unit.	92
MX-KBX2	93
1. Unpacking	93
A. Check the parts in the package	93
2. Installation	93
A. Turn off the power of the main unit	93
B. Install the USB hub PWB.	93
C. Install the base unit	94
D. Install the operation panel	95
E. Adjust the position of the key top unit	96
F. Turn on the power of the main unit	96
G. Check the keyboard input	96
H. Language setting	96
MX-AMX1	98
1. Unpacking	98
A. Check the packed items	98
2. Installation	98
A. Make preparations to enable the Application Integration Module function.	98
B. Check the operation of the Application Integration Module function.	98
MX-AMX2	99
1. Unpacking	99
A. Check the packed items	99
2. Installation	99
A. Make preparations for enabling the Application Communication Module	99
B. External application setup	99
MX-AMX3	100
1. Unpacking	100
A. Check the packed items	100
2. Installation	100
A. Make preparations for enabling the external account kit.	100
B. Set the external application.	100
Dehumidifying heater	101
1. Parts included	101
2. Installation	101
A. Removal of the rear cabinet and the left rear lower cabinet	101
B. Installation of the heater electric component kit	101
C. Installation of the heater kit	103
D. Installation of the rear cabinet and the left rear lower cabinet	104
E. Installation of the scanner heater kit	104
F. Operation check after installation	106
MX-RP11	107
1. Unpacking	107
A. Removal of the RSPF	107
B. Check the packed items	107
2. Installation	107
A. Turn off the power of the main unit.	107
B. RSPF unit installation	107
C. RSPF parallelism adjustment	109
D. RSPF skew adjustment (Front surface mode)	112
E. RSPF paper feed tray paper width sensor adjustment	113