Home » Netgear Manuals » Hubs & Switches » Netgear GSM7212P » Manual Viewer

Netgear GSM7212P GSM5212P/GSM7212P/GSM7212F/GSM7224P User Manual - Page 28

DHCP Vendor Class Identifier String, Locally Administered MAC Address

Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Web Management User Guide Once you have established in-band connectivity, you can change the IP information using any of the following: • Terminal interface via the EIA-232 port • Terminal interface via telnet • SNMP-based management • Web-based management 1. Use IP Address to specify the IP address of the interface. The factory default value is 169.254.100.100. 2. Use Subnet Mask to enter the IP subnet mask for the interface. The factory default value is 255.255.0.0. 3. Use Default Gateway to specify the default gateway for the IP interface. The factory default value is 0.0.0.0 4. Use Locally Administered MAC Address to configure a locally administered MAC address for in-band connectivity instead of using the burned-in universally administered MAC address. In addition to entering an address in this field, you must also set the MAC address type to locally administered. Enter the address as twelve hexadecimal digits (6 bytes) with a colon between each byte. Bit 1 of byte 0 must be set to a 1 and bit 0 to a 0, in other words, byte 0 must have a value between x'40' and x'7F'. 5. Use MAC Address type to specify whether the burned-in or the locally administered MAC address should be used for in-band connectivity. The factory default is to use the burned-in MAC address 6. Use Current Network Configuration Protocol to specify what the switch should do following power-up: transmit a Bootp request, transmit a DHCP request, or do nothing (none). The factory default is DHCP. 7. Use DHCP Vendor Class Identifier to enable DHCP VendorId option on the client. 8. Use DHCP Vendor Class Identifier String to specify DHCP VendorId option string on the client. 9. Use Management VLAN ID to specify the management VLAN ID of the switch. It may be configured to any value in the range of 1 - 4093. The management VLAN is used for management of the switch. This field is configurable for administrative users and read-only for other users. The following table describes IPv4 Network Configuration information. Field Burned In MAC Address Description The burned-in MAC address used for in-band connectivity if you choose not to configure a locally administered address. 28

Section	Page
ProSafe® Managed Switch	1
Contents	3
1. Getting Started	8
Switch Management Interface	8
Web Access	8
Understanding the User Interfaces	9
Using the Web Interface	9
Using SNMP	14
Interface Naming Convention	14
2. Configuring System Information	16
Management	16
System Information	16
Switch Statistics	21
System CPU Status	24
Loopback Interface	26
Network Interface	27
Time	31
DNS	38
SDM Template Preference	40
Services	42
DHCP Server	42
DHCP Relay	51
DHCP L2 Relay	52
UDP Relay	55
PoE	57
Basic	57
Advanced	59
SNMP	64
SNMPV1/V2	64
SNMP V3	70
LLDP	71
LLDP	72
LLDP-MED	78
ISDP	87
Basic	87
Advanced	88
Timer Schedule	93
Timer Global Configuration	93
Timer Schedule Configuration	94
3. Configuring Switching Information	96
VLANs	96
Basic	97
Advanced	99
Spanning Tree Protocol	112
Basic	112
Advanced	115
Multicast	127
MFDB	127
IGMP Snooping	129
MLD Snooping	140
MVR Configuration	147
Basic	147
Advanced	148
Address Table	152
Basic	152
Advanced	154
Ports	158
Port Configuration	158
Port Description	160
Link Aggregation Groups	161
LAG Configuration	162
LAG Membership	163
4. Routing	166
Routing Table	166
Basic	167
Advanced	169
IP	171
Basic	171
Advanced	178
VLAN	186
VLAN Routing Wizard	187
VLAN Routing Configuration	188
ARP	189
Basic	189
Advanced	190
Router Discovery	193
5. Configuring Quality of Service	196
Class of Service	197
Basic	197
Advanced	199
Differentiated Services	204
DiffServ Wizard	205
Auto VoIP Configuration	207
Basic	207
Advanced	209
6. Managing Device Security	224
Management Security Settings	224
Local User	224
Enable Password Configuration	227
Line Password Configuration	227
RADIUS	228
Configuring TACACS+	234
Authentication List Configuration	236
Login Sessions	240
Configuring Management Access	241
HTTP	241
HTTPS	243
SSH	246
Telnet	249
Console Port	251
Denial of Service	252
Port Authentication	253
Basic	254
Advanced	255
Traffic Control	262
MAC Filter	263
Port Security	265
Private Group	270
Protected Ports Configuration	272
Storm Control	273
Control	275
DHCP Snooping	275
IP Source Guard	281
Dynamic ARP Inspection	283
Configuring Access Control Lists	288
ACL Wizard	288
Basic	289
Advanced	294
7. Monitoring the System	308
Ports	308
Port Statistics	309
Port Detailed Statistics	311
EAP Statistics	317
Cable Test	320
Logs	321
Buffered Logs	322
Command Log Configuration	324
Console Log Configuration	324
SysLog Configuration	325
Trap Logs	326
Event Logs	328
Persistent Logs	329
Port Mirroring	330
Multiple Port Mirroring	330
sFlow	332
Basic	332
Advanced	333
8. Maintenance	336
Save Configuration	336
Save Configuration	336
Auto Install Configuration	337
Reset	337
Device Reboot	338
Factory Default	338
Password Reset	339
Upload File From Switch	339
File Upload	340
HTTP File Upload	341
USB File Upload	342
Download File To Switch	342
File Download	343
HTTP File Download	344
USB File Download	346
File Management	347
Copy	347
Dual Image Configuration	348
Troubleshooting	349
Ping IPv4	349
Ping IPv6	350
Traceroute IPv4	351
Traceroute IPv6	352
9. Help	354
Online Help	354
Support	354
User Guide	355
A. Default Settings	357
B. Configuration Examples	361
Virtual Local Area Networks (VLANs)	361
VLAN Example Configuration	362
Access Control Lists (ACLs)	363
MAC ACL Example Configuration	364
Standard IP ACL Example Configuration	365
Differentiated Services (DiffServ)	366
Class	366
DiffServ Traffic Classes	367
Creating Policies	367
DiffServ Example Configuration	368
802.1X	370
802.1X Example Configuration	371
MSTP	372
MSTP Example Configuration	374
C. Notification of Compliance	378

Match case Limit results 1 per page

Web Management User Guide

Once you have established in-band connectivity, you can change the IP information using

any of the following:

•

Terminal interface via the EIA-232 port

•

Terminal interface via telnet

•

SNMP-based management

•

Web-based management

Use

IP Address

to specify the IP address of the interface. The factory default value is

169.254.100.100.

Use

Subnet Mask

to enter the IP subnet mask for the interface. The factory default value is

255.255.0.0.

Use

Default Gateway

to specify the default gateway for the IP interface. The factory default

value is 0.0.0.0

Use

Locally Administered MAC Address

to configure a locally administered MAC address

for in-band connectivity instead of using the burned-in universally administered MAC

address. In addition to entering an address in this field, you must also set the MAC address

type to locally administered. Enter the address as twelve hexadecimal digits (6 bytes) with a

colon between each byte. Bit 1 of byte 0 must be set to a 1 and bit 0 to a 0, in other words,

byte 0 must have a value between x'40' and x'7F'.

Use

MAC Address type

to specify whether the burned-in or the locally administered MAC

address should be used for in-band connectivity. The factory default is to use the burned-in

MAC address

Use

Current Network Configuration Protocol

to specify what the switch should do

following power-up: transmit a Bootp request, transmit a DHCP request, or do nothing

(none). The factory default is DHCP.

Use

DHCP Vendor Class Identifier

to enable DHCP VendorId option on the client.

Use

DHCP Vendor Class Identifier String

to specify DHCP VendorId option string on the

client.

Use

Management VLAN ID

to specify the management VLAN ID of the switch. It may be

configured to any value in the range of 1 - 4093. The management VLAN is used for

management of the switch. This field is configurable for administrative users and read-only

for other users.

The following table describes IPv4 Network Configuration information.

Field

Description

Burned In MAC Address

The burned-in MAC address used for in-band

connectivity if you choose not to configure a locally

administered address.