Home » Intel Manuals » Motherboards » Intel BFCBASE » Manual Viewer

Intel BFCBASE Data Sheet - Page 47

Differential Clock Waveform, Differential Clock Crosspoint Specification

UPC - 735858197373

Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Electrical Specifications Figure 2-13. Differential Clock Waveform BCLK1 Threshold Region BCLK0 Crossing Voltage Crossing Voltage Tp Tp = T1: BCLK[1:0] period Ringback Margin Overshoot VH Rising Edge Ringback Falling Edge Ringback, VL Undershoot Figure 2-14. Differential Clock Crosspoint Specification Crossing Point (mV) 650 600 550 500 550 + 0.5 (VHavg - 700) 450 550 mV 400 250 + 0.5 (VHavg - 700) 350 300 250 mV 250 200 660 670 680 690 700 710 720 730 740 750 760 770 780 790 800 810 820 830 840 850 VHavg (mV) Document Number: 318080-002 47

Section	Page
1 Introduction	9
1.1 Terminology	11
1.2 State of Data	13
1.3 References	13
2 Electrical Specifications	15
2.1 Front Side Bus and GTLREF	15
2.2 Decoupling Guidelines	15
2.2.1 VCC Decoupling	16
2.2.2 VTT Decoupling	16
2.2.3 Front Side Bus AGTL+ Decoupling	16
2.3 Front Side Bus Clock (BCLK[1:0]) and Processor Clocking	16
2.3.1 Front Side Bus Frequency Select Signals (BSEL[2:0])	17
2.3.2 PLL Power Supply	17
2.4 Voltage Identification (VID)	17
2.5 Reserved, Unused, or Test Signals	20
2.6 Front Side Bus Signal Groups	20
2.7 CMOS Asynchronous and Open Drain Asynchronous Signals	22
2.8 Test Access Port (TAP) Connection	22
2.9 Mixing Processors	23
2.10 Absolute Maximum and Minimum Ratings	23
2.11 Processor DC Specifications	24
2.11.1 Flexible Motherboard Guidelines (FMB)	25
2.11.2 Platform Environmental Control Interface (PECI) DC Specifications	35
2.11.3 VCC Overshoot Specification	37
2.11.4 AGTL+ FSB Specifications	38
2.12 Front Side Bus AC Specifications	40
2.13 Processor AC Timing Waveforms	45
3 Mechanical Specifications	57
3.1 Package Mechanical Drawing	57
3.2 Processor Component Keepout Zones	60
3.3 Package Loading Specifications	66
3.4 Package Handling Guidelines	67
3.5 Package Insertion Specifications	67
3.6 Processor Mass Specifications	67
3.7 Processor Materials	67
3.8 Processor Markings	68
3.9 Processor Pin-Out Coordinates	69
4 Pin Listing	71
4.1 Pin Assignments	71
4.1.1 Pin Listing by Pin Name	71
4.1.2 Pin Listing by Pin Number	79
5 Signal Definitions	87
5.1 Signal Definitions.	87
6 Thermal Specifications	95
6.1 Package Thermal Specifications	95
6.1.1 Thermal Specifications	95
6.1.2 Thermal Metrology	102
6.2 Processor Thermal Features	103
6.2.1 Thermal Monitor Features	103
6.2.2 Thermal Monitor	103
6.2.3 Thermal Monitor 2	104
6.2.4 On-Demand Mode	105
6.2.5 PROCHOT# Signal	106
6.2.6 FORCEPR# Signal	106
6.2.7 THERMTRIP# Signal	106
6.3 Platform Environment Control Interface (PECI)	107
6.3.1 Introduction	107
6.3.2 PECI Specifications	108
7 Features	111
7.1 Power-On Configuration Options	111
7.2 Clock Control and Low Power States	111
7.2.1 Normal State	112
7.2.2 HALT or Extended HALT State	112
7.2.3 Stop-Grant State	114
7.2.4 Extended HALT Snoop or HALT Snoop State, Stop Grant Snoop State	115
7.3 Enhanced Intel SpeedStep® Technology	115
7.4 System Management Bus (SMBus) Interface	116
7.4.1 SMBus Device Addressing	117
7.4.2 PIROM and Scratch EEPROM Supported SMBus Transactions	118
7.4.3 Processor Information ROM (PIROM)	119
7.4.4 Checksums	137
7.4.5 Scratch EEPROM	137
8 Boxed Processor Specifications	139
8.1 Introduction	139
8.2 Thermal Specifications	139
8.2.1 Boxed Processor Cooling Requirements	139
9 Debug Tools Specifications	141
9.1 Debug Port System Requirements	141
9.2 Logic Analyzer Interface (LAI)	141
9.2.1 Mechanical Considerations	141