Dell 3130cn User's Guide (PDF) - Page 128

Status, Reset Wireless, TCP/IP

Page 128 highlights

Values: Auto* Detects the Ethernet settings automatically. 10Base Half Uses 10base-T half-duplex. 10Base Full Uses 10base-T full-duplex. 100Base Half Uses 100base-TX half-duplex. 100Base Full Uses 100base-TX full-duplex. Status Purpose: To display the information on the wireless signal strength. Any change cannot be made on the operator panel to improve the status of the wireless connection. Values: Good Indicates good signal strength. Acceptable Indicates marginal signal strength. Low Indicates insufficient signal strength. No Reception Indicates that no signal is received. NOTE: This item is only displayed when an optional wireless printer adapter is installed. Reset Wireless Purpose: To initialize wireless network settings. After executing this function and rebooting the printer, all wireless network settings are reset to their default values. NOTE: This item is only displayed when an optional wireless printer adapter is installed. TCP/IP Purpose: To configure TCP/IP settings. The change becomes effective after the printer is turned off and then on again. Values: IP Mode IPv4 Dual Stack* Uses both IPv4 and IPv6 to set the IP address. IPv4 Mode Uses IPv4 to set the IP address. IPv6 Mode Get IP Address IP Address Subnet Mask Uses IPv6 to set the IP address. AutoIP* Automatically sets the IP address. BOOTP Uses BOOTP to set the IP address. RARP Uses RARP to set the IP address. DHCP Uses DHCP to set the IP address. Panel Enables the IP address entered on the operator panel. Sets the IP address allocated to the printer by using the keys on the operator panel. Sets the subnet mask.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308

Values:
Auto*
Detects the Ethernet settings automatically.
10Base Half
Uses 10base-T half-duplex.
10Base Full
Uses 10base-T full-duplex.
100Base Half
Uses 100base-TX half-duplex.
100Base Full
Uses 100base-TX full-duplex.
Status
Purpose:
To display the information on the wireless signal strength. Any change cannot be made on the operator panel to improve
the status of the wireless connection.
Values:
Good
Indicates good signal strength.
Acceptable
Indicates marginal signal strength.
Low
Indicates insufficient signal strength.
No Reception
Indicates that no signal is received.
NOTE:
This item is only displayed when an optional wireless printer adapter is installed.
Reset Wireless
Purpose:
To initialize wireless network settings. After executing this function and rebooting the printer, all wireless network settings
are reset to their default values.
NOTE:
This item is only displayed when an optional wireless printer adapter is installed.
TCP/IP
Purpose:
To configure TCP/IP settings. The change becomes effective after the printer is turned off and then on again.
Values:
IP
Mode
Dual Stack*
Uses both IPv4 and IPv6 to set the IP address.
IPv4 Mode
Uses IPv4 to set the IP address.
IPv6 Mode
Uses IPv6 to set the IP address.
IPv4
Get IP
Address
AutoIP*
Automatically sets the IP address.
BOOTP
Uses BOOTP to set the IP address.
RARP
Uses RARP to set the IP address.
DHCP
Uses DHCP to set the IP address.
Panel
Enables the IP address entered on the operator panel.
IP Address
Sets the IP address allocated to the printer by using the keys on the operator
panel.
Subnet Mask
Sets the subnet mask.