Dell PowerEdge R815 Hardware Owner's Manual - Page 122

VFlash Media (Optional), Removing a VFlash Media Card

Get Dell PowerEdge R815 PDF manuals and user guides View all Dell PowerEdge R815 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 122 highlights

3 Remove the plastic filler plug for the iDRAC6 Enterprise port from the system back panel. See Figure 1-3. 4 Align the front edge of the card with the two plastic retention standoffs next to the iDRAC6 connector on the system board, and lower the card into place. See Figure 3-21 and Figure 6-1. When the front of the card is fully seated, the plastic standoffs snap over the edge of the card. 5 If applicable, connect the Ethernet cable from the iDRAC6 Enterprise Card connector on the system back panel. See Figure 1-3. 6 Close the system. See "Closing the System" on page 77. 7 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. 8 Enter the iDRAC6 configuration utility and set up the Ethernet mode. See "iDRAC6 Configuration Utility" on page 71. VFlash Media (Optional) The VFlash media card is a Secure Digital (SD) card that plugs into the optional iDRAC6 Enterprise card at the back corner of the system. Removing a VFlash Media Card To remove the VFlash media, push inward on the card to release it, and pull the card from the card slot. Installing a VFlash Media Card 1 Locate the VFlash media slot at the back corner of the system. See Figure 1-3. 2 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module. NOTE: The slot is keyed to ensure correct insertion of the card. 3 Press inward on the card to lock it into the slot. 122 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
122
Installing System Components
3
Remove the plastic filler plug for the iDRAC6 Enterprise port from the
system back panel. See Figure 1-3.
4
Align the front edge of the card with the two plastic retention standoffs
next to the iDRAC6 connector on the system board, and lower the card
into place. See Figure 3-21 and Figure 6-1.
When the front of the card is fully seated, the plastic standoffs snap over
the edge of the card.
5
If applicable, connect the Ethernet cable from the iDRAC6 Enterprise
Card connector on the system back panel. See Figure 1-3.
6
Close the system. See "Closing the System" on page 77.
7
Reconnect the system to its electrical outlet and turn the system on,
including any attached peripherals.
8
Enter the iDRAC6 configuration utility and set up the Ethernet mode. See
"iDRAC6 Configuration Utility" on page 71.
VFlash Media (Optional)
The VFlash media card is a Secure Digital (SD) card that plugs into the
optional iDRAC6 Enterprise card at the back corner of the system.
Removing a VFlash Media Card
To remove the VFlash media, push inward on the card to release it, and pull
the card from the card slot.
Installing a VFlash Media Card
1
Locate the VFlash media slot at the back corner of the system. See
Figure 1-3.
2
With the label side facing up, insert the contact-pin end of the SD card
into the card slot on the module.
NOTE:
The slot is keyed to ensure correct insertion of the card.
3
Press inward on the card to lock it into the slot.