Epson PowerLite 735c User Manual - Page 26

Shutting Down the Projector

Get Epson PowerLite 735c PDF manuals and user guides View all Epson PowerLite 735c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

note When the projector has not received any input signals for 30 minutes, it automatically turns off the projector lamp and enters "sleep mode." This conserves electricity, cools the projector, and extends the life of the lamp. If you want to start projecting again, press the Power button. If you are done using the projector, unplug the power cord. To turn off sleep mode, see page 81. Shutting Down the Projector When you've finished using the projector, follow the recommended procedure to shut it down. This extends the life of the lamp and protects the projector from possible overheating. 1. If you've connected a computer or laptop, shut it down first; otherwise you may not be able to see your computer's display to shut it down properly. 2. To turn off the projector, press the red P Power button on the projector or remote control. Power button caution To avoid damaging the projector or lamp, never unplug the power cord when the power light is green or flashing orange. You see a confirmation message. (If you don't want to turn it off, press any other button.) 3. Press the Power button again. The power light flashes orange for about a minute and a half as the projector cools down. After the projector has cooled, the orange light stays on and the exhaust fan shuts off. If you want to turn the projector on again, wait until the orange light stops flashing. Then press the Power button. 4. Turn off and disconnect any equipment plugged into the projector. 5. If you extended the feet, press the side buttons to retract them. 6. Replace the lens cap and unplug the power cord. 7. Store the projector in a protective case. 20 Displaying and Adjusting the Image

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
20
Displaying and Adjusting the Image
Shutting Down the Projector
When you’ve finished using the projector, follow the recommended
procedure to shut it down. This extends the life of the lamp and
protects the projector from possible overheating.
1.
If you’ve connected a computer or laptop, shut it down first;
otherwise you may not be able to see your computer’s display to
shut it down properly.
2.
To turn off the projector, press the red
P
Power
button on the
projector or remote control.
You see a confirmation message. (If you don’t want to turn it off,
press any other button.)
3.
Press the
Power
button again. The power light flashes orange for
about a minute and a half as the projector cools down. After the
projector has cooled, the orange light stays on and the exhaust fan
shuts off.
If you want to turn the projector on again, wait until the orange
light stops flashing. Then press the
Power
button.
4.
Turn off and disconnect any equipment plugged into the
projector.
5.
If you extended the feet, press the side buttons to retract them.
6.
Replace the lens cap and unplug the power cord.
7.
Store the projector in a protective case.
note
When the projector has not
received any input signals
for 30 minutes, it
automatically turns off the
projector lamp and enters
“sleep mode.” This conserves
electricity, cools the
projector, and extends the
life of the lamp. If you want
to start projecting again,
press the
Power
button. If
you are done using the
projector, unplug the power
cord. To turn off sleep mode,
see page 81.
Power button
caution
To avoid damaging the
projector or lamp, never
unplug the power cord when
the power light is green or
flashing orange.