HP Integrity rx2800 HP Integrity iLO 3 Operations Guide - Page 57

PR: Set power restore policy, PS: Power status, RS: Reset system through the RST signal

Get HP Integrity rx2800 - i2 PDF manuals and user guides View all HP Integrity rx2800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

PR: Set power restore policy Command access level: MP configuration access The PR command configures the power restore policy. The power restore policy determines how the system behaves when AC power returns after an AC power loss. • If PR is set to On or Previous, the system powers on after AC is applied. • If PR is set to Off, the system stays powered off after AC is applied. To power on the system, push the system power button or run the PC command. • If PR is set to Previous, the power is restored to the state that was in effect when the AC power was removed or lost. Command line usage and scripting: PR [ -policy ] [ -nc ] PR -? See also: PC PS: Power status Command access level: Login access The PS command displays the system power status. Command line usage and scripting: PS [ -nc ] PS -? See also PC, SS. RS: Reset system through the RST signal Command access level: Power control access IMPORTANT: During normal system operation, shut down the operating system before issuing the RS command. The RS command resets the system (except iLO 3) through the RST signal. Running this command irrecoverably halts all system processing and I/O activity and restarts the system. The effect of this command is similar to cycling the system power. The operating system is not notified, no dump is taken as the system shuts down, and so on. Command line usage and scripting: RS [ -nc ] RS -? See also: TC SA: Set access Command access level: MP configuration access The SA command configures the access mode for the LAN and the Command mode. You can set iLO 3 to enable web or SSH access. SSH and web SSL is enabled by default. If LAN users are connected when a disable from this command runs, they are disconnected. Any future incoming connection request to the corresponding port is rejected. A message appears prior to being rejected. NOTE: Currently, when an access method is first set to disabled, the message is sent. However, after an iLO reboot, the port is not opened. Command line usage and scripting: Text user interface 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
PR
: Set power restore policy
Command access level: MP configuration access
The
PR
command configures the power restore policy. The power restore policy determines how
the system behaves when AC power returns after an AC power loss.
•
If
PR
is set to
On
or
Previous
, the system powers on after AC is applied.
•
If
PR
is set to
Off
, the system stays powered off after AC is applied. To power on the system,
push the system power button or run the
PC
command.
•
If
PR
is set to
Previous
, the power is restored to the state that was in effect when the AC
power was removed or lost.
Command line usage and scripting
:
PR [ -policy <on|off|previous> ] [ -nc ]
PR -?
See also:
PC
PS
: Power status
Command access level: Login access
The
PS
command displays the system power status.
Command line usage and scripting
:
PS [ -nc ]
PS -?
See also
PC, SS
.
RS
: Reset system through the RST signal
Command access level: Power control access
IMPORTANT:
During normal system operation, shut down the operating system before issuing
the
RS
command.
The
RS
command resets the system (except iLO 3) through the RST signal.
Running this command irrecoverably halts all system processing and I/O activity and restarts the
system. The effect of this command is similar to cycling the system power. The operating system is
not notified, no dump is taken as the system shuts down, and so on.
Command line usage and scripting
:
RS [ -nc ]
RS -?
See also:
TC
SA
: Set access
Command access level: MP configuration access
The
SA
command configures the access mode for the LAN and the Command mode. You can set
iLO 3 to enable web or SSH access. SSH and web SSL is enabled by default.
If LAN users are connected when a disable from this command runs, they are disconnected. Any
future incoming connection request to the corresponding port is rejected. A message appears prior
to being rejected.
NOTE:
Currently, when an access method is first set to disabled, the message is sent. However,
after an iLO reboot, the port is not opened.
Command line usage and scripting
:
Text user interface
57