Home » IBM Manuals » Desktops » IBM 620410U » Manual Viewer

IBM 620410U User Guide - Page 68

Power and signal cables for internal drives, If the cable has two connectors

UPC - 087944665410

View all IBM 620410U manuals

Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

11. Connect one end of the IDE signal cable into the back of the drive and the other end of the cable into the IDE connector on the system board. For the location of the IDE connectors, see "System board internal cable connectors" on page 42. Note: Make sure to route the signal cable so that it does not block the air flow to the rear of the drives or over the microprocessor. 12. Connect a power cable to the back of the drive. The connectors are keyed and can be inserted only one way. 13. If you have other options to install or remove, do so now. 14. Go to the appropriate section to work with another option, or replace the cover. See "Replacing the cover" on page 55 for details. 15. Reconnect the external cables and power cords; then turn on the attached devices and the computer. Power and signal cables for internal drives: Your computer uses cables to connect IDE devices to the power supply and to the system board. The following cables are provided: v Four-wire power cables connect the drives to the power supply. At the end of these cables are plastic connectors that attach to different drives; these connectors vary in size. Also, certain power cables attach to the system board. v Flat signal cables, also called ribbon cables, connect IDE and diskette drives to the system board. There are two sizes of ribbon cables that come with your computer. - The wider IDE signal cable has two or three connectors. - If the cable has three connectors, one of these connectors is attached to the drive, one is a spare, and the third attaches to the primary or secondary IDE connector on the system board. - If the cable has two connectors, one of these connectors is attached to the hard disk drive, and the other attaches to the primary or secondary IDE connector on the system board. Note: The CD-ROM drive will have an ATA 66 signal cable. ATA 66 signal cables are color-coded. The blue connector attaches to the system board. The black connector attaches to the primary device. The gray middle connector attaches to the secondary device. If you are installing a hard disk drive, you must change the switch setting on the CD-ROM drive to secondary and change the connector used for the CD-ROM drive to the gray middle connector. - The narrower signal cable has two connectors, one to attach to the diskette drive, and the other to attach to the connector (FDD1) on the system board. To locate connectors on the system board, see "System board internal cable connectors" on page 42. 52 IBM IntelliStation E Pro Types 6204 and 6214: User's Guide

Section	Page
Contents	5
Safety information	9
Preface	15
Related Publications	15
Notices and statements used in this book	15
Chapter 1. Introducing the IntelliStation E Pro	17
Features and specifications for the desktop model	18
Features and specifications for the tower model	19
Inventory checklist	20
Software	20
Preinstalled software	20
Software Selections CD	22
Device Driver and IBM Enhanced Diagnostics CD	22
Other software	22
What your computer offers	22
Reliability, availability, and serviceability features	23
Computer controls and indicators	24
Chapter 2. Setting up your computer	27
Selecting a location for your computer	27
Arranging your workspace	27
Comfort	27
Glare and lighting	28
Air circulation	28
Electrical outlets and cable lengths	28
Moving the stabilizing feet	28
Setting the voltage-selection switch	29
Connecting computer cables	30
Recording important numbers	32
Running the operating system setup program	32
Registering your computer	33
Using Access IBM	33
Installing other operating systems	34
Product Recovery Program	34
Creating emergency diskettes	35
Creating a Recovery Repair diskette	35
Creating a Norton AntiVirus Rescue diskette	35
Chapter 3. Operating your computer	37
Turning on your computer	37
Using video features	37
Video device drivers	38
Changing monitor settings	38
Using audio features	39
Line in	39
Line out	39
Microphone	39
Managing your computer on a network	39
Wake on LAN	39
Intel Boot Agent	40
LANClient Control Manager (LCCM)	40
System Migration Assistant	40
Desktop Management Interface	40
Using security features	40
Anti-intrusion features	40
Component protection	41
Data protection	41
SMART hard disk drive	41
SMART Reaction	41
Virus protection	41
Locking the keyboard	41
Shutting down your operating system	42
Turning off your computer	42
Chapter 4. Configuring your computer	45
Using the IBM Setup Utility program	45
Starting the IBM Setup Utility program	45
IBM Setup Utility main menu choices	46
Main	46
Devices	46
Startup	47
Advanced	47
Security	48
Power	49
Exit	50
Using the SCSISelect Utility program (some models)	50
Starting the SCSISelect Utility program	50
SCSISelect menu choices	50
Using the Intel Boot Agent Utility program	51
Starting the Intel Boot Agent Utility program	52
Intel Boot Agent Utility menu choices	52
Chapter 5. Installing options	55
Before you begin	55
System reliability considerations	55
Handling static-sensitive devices	55
Desktop model	56
Major components of the desktop model	56
System board	57
System board internal cable connectors	58
System board external cable connectors	58
CMOS recovery jumper	59
Installing options in a desktop model	59
Removing the cover	59
Removing the frame support bracket	60
Working with adapters	60
Installing internal drives	64
Installing memory modules	69
Installing a security U-bolt	70
Replacing the cover	71
Tower model	72
Major components of the tower model	72
System and PCI extender boards	73
System board internal cable connectors	74
System board external connectors	75
CMOS recovery jumper	76
Installing options in a tower model	76
Removing the side cover	76
Removing the support bracket	77
Working with adapters	78
Installing internal drives	83
Installing memory modules	89
Installing a security U-bolt	91
Replacing the cover	92
Connecting external options	92
Input/output connector locations	93
Input/output connectors	94
Video connector	94
Keyboard connector	95
Mouse connector	95
Parallel connector	95
Serial connectors	96
Ethernet connector	96
Universal Serial Bus connectors	96
Audio connectors	97
Ultra160 SCSI connector	97
Chapter 6. Solving problems	99
Diagnostic tools overview	99
Power-on self-test (POST)	101
Small computer system interface (SCSI) messages (some models)	101
Diagnostic programs and error messages	102
Text messages	102
Starting the diagnostic programs	103
Using the Device Driver and IBM Enhanced Diagnostics CD	103
Creating an IBM Enhanced Diagnostics diskette	103
Using the Enhanced diagnostics diskette	104
Viewing the test log	104
Diagnostic error message tables	105
Other diagnostic programs	109
Troubleshooting charts	109
Software error messages	113
Troubleshooting the Ethernet controller	113
Network connection problems	113
Ethernet controller troubleshooting chart	114
Ethernet controller messages	115
Novell NetWare or IntraNetWare computer ODI driver teaming messages	115
NDIS 4.0 (Windows 2000 and Windows XP) Event Viewer messages	117
Ethernet teaming messages	119
Intel Boot Agent messages	121
Recovering your operating system and preinstalled software	122
Recovering or installing device drivers	122
Recovering the operating system	123
Performing a partial or full recovery	123
Using the Recovery Repair diskette	123
Using ConfigSafe and the Save Our System (SOS) feature	124
Erasing a lost or forgotten password (clearing CMOS)	125
Recovering from a POST/BIOS update failure	126
Replacing the battery	127
Getting information, help, and service	128
Before you call	128
Using the documentation	129
Getting help and information from the World Wide Web	129
Software service and support	129
Hardware service and support	129
Appendix A. Using the Software Selections CD	131
Features of the Software Selections CD	131
Starting the Software Selections CD	131
Installing software using the Software Selections CD	132
Appendix B. Caring for your computer	133
Basics	133
Cleaning your computer	133
Computer and keyboard	133
Monitor screen	133
Mouse	133
Moving your computer	134
Appendix C. Computer records	137
Serial numbers and keys	137
Appendix D. Viewing the license agreement	139
Appendix E. Warranty information	141
Warranty period	141
Problem determination	141
Running diagnostics	141
Checking software	141
Warranty service and support	142
International Warranty Service	142
Purchasing additional services	143
IBM Statement of Limited Warranty Z125-4753-06 8/2000	144
Part 1 - General Terms	144
Part 2 - Country-unique Terms	146
Appendix F. Notices	153
Edition notice	153
Trademarks	154
Important notes	154
Electronic emission notices	155
Federal Communications Commission (FCC) statement	155
Industry Canada Class A emission compliance statement	155
Australia and New Zealand Class A statement	155
United Kingdom telecommunications safety requirement	156
European Union EMC Directive conformance statement	156
Taiwan electrical emission statement	156
Japanese Voluntary Control Council for Interference (VCCI) statement	156
Power cords	156

Match case Limit results 1 per page

11.

Connect one end of the IDE signal cable into the back of the drive and the

other end of the cable into the IDE connector on the system board. For the

location of the IDE connectors, see

“

System board internal cable connectors

”

on page 42.

Note:

Make sure to route the signal cable so that it does not block the air flow

to the rear of the drives or over the microprocessor.

12.

Connect a power cable to the back of the drive. The connectors are keyed and

can be inserted only one way.

13.

If you have other options to install or remove, do so now.

14.

Go to the appropriate section to work with another option, or replace the cover.

See

“

Replacing the cover

”

on page 55 for details.

15.

Reconnect the external cables and power cords; then turn on the attached

devices and the computer.

Power and signal cables for internal drives:

Your computer uses cables to

connect IDE devices to the power supply and to the system board. The following

cables are provided:

Four-wire power cables connect the drives to the power supply. At the end of

these cables are plastic connectors that attach to different drives; these

connectors vary in size. Also, certain power cables attach to the system board.

Flat signal cables, also called ribbon cables, connect IDE and diskette drives to

the system board. There are two sizes of ribbon cables that come with your

computer.

–

The wider IDE signal cable has two or three connectors.

If the cable has three connectors, one of these connectors is attached to

the drive, one is a spare, and the third attaches to the primary or secondary

IDE connector on the system board.

If the cable has two connectors, one of these connectors is attached to the

hard disk drive, and the other attaches to the primary or secondary IDE

connector on the system board.

Note:

The CD-ROM drive will have an ATA 66 signal cable. ATA 66 signal

cables are color-coded. The blue connector attaches to the system

board. The black connector attaches to the primary device. The gray

middle connector attaches to the secondary device. If you are installing

a hard disk drive, you must change the switch setting on the CD-ROM

drive to secondary and change the connector used for the CD-ROM

drive to the gray middle connector.

–

The narrower signal cable has two connectors, one to attach to the diskette

drive, and the other to attach to the connector (FDD1) on the system board.

To locate connectors on the system board, see

“

System board internal cable

connectors

”

on page 42.

IBM IntelliStation E Pro Types 6204 and 6214: User

’

s Guide