Lenovo NetVista X40 Quick Reference for NetVista 2179 and 6643 systems (Dutch) - Page 28

Starting your computer for the first time, Important, Attention

Page 28 highlights

v Connect the Ethernet cable to the RJ-45 Ethernet connector. Important: To operate the computer within FCC Class A limits, use a category 5 Ethernet cable. Ethernet 3. Connect the power cord to the power connector located on the rear of the computer. If there is a label covering the power connector, remove it. Power Voltage switch 115 Attention: If you have a desktop model, check the position of the voltage-selection switch. Use a ball point pen to slide the switch, if necessary. v If the voltage supply range in your location is 90-137 V ac, set the voltage switch to 115 V. v If the voltage supply range in your location is 180-265 V ac, set the voltage switch to 230-265 V. 4. Connect the power cords into properly grounded electrical outlets. Note: When the power cord is first plugged in, the computer might turn on for a few seconds, then turn off. This is normal. Starting your computer for the first time This section contains the information that you will need to start operating your computer. 1. Review the safety precautions listed in Statement 1 and Statement 5 in "Safety" on page v. 2. If your computer is a desktop model, set the voltage-selection switch located next to the power cord connector on the rear of the computer. 12 IBM® IntelliStation® E Pro: User's Guide IntelliStation E Pro Types 6836, 6846

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156

v
Connect the Ethernet cable to the RJ-45 Ethernet connector.
Important:
To operate the computer within FCC Class A limits, use a category 5
Ethernet cable.
3.
Connect the power cord to the power connector located on the rear of the
computer. If there is a label covering the power connector, remove it.
Attention:
If you have a desktop model, check the position of the
voltage-selection switch. Use a ball point pen to slide the switch, if necessary.
v
If the voltage supply range in your location is 90-137 V ac, set the voltage
switch to 115 V.
v
If the voltage supply range in your location is 180-265 V ac, set the voltage
switch to 230-265 V.
4.
Connect the power cords into properly grounded electrical outlets.
Note:
When the power cord is first plugged in, the computer might turn on for
a few seconds, then turn off. This is normal.
Starting your computer for the first time
This section contains the information that you will need to start operating your
computer.
1.
Review the safety precautions listed in Statement 1 and Statement 5 in
Safety
on page v.
2.
If your computer is a desktop model, set the voltage-selection switch located
next to the power cord connector on the rear of the computer.
Ethernet
Power
Voltage switch
115
12
IBM
®
IntelliStation
®
E Pro: User
s Guide IntelliStation E Pro Types 6836, 6846