Xerox 8500DN Service Manual - Page 369

Index Numerics 525-sheet feeder, parts list, 9-9 8-pin NVRAM, parts list, 9-13 A AC power, 2-20 adjust x-axis scale, service menu, 4-3 B back button, 1-5 basic positions, printhead, 2-10 basic printhead cleaning cycle, 2-33 belts drive, single reduction, 2-16 drum, 2-17 parts for wiper drive, 9-7 parts for y-axis, 9-7 printer, 7-6 removing from drum assembly, 8-27 wiper alignment, 6-3 y-axis disassembly, 8-8 y-axis slip test, 3-56, 4-40 y-axis tension, 3-13 y-axis tension test, 4-40 BIST Error Codes, 3-3 C cables circuit board and cables part list, 9-13 crossover, 4-71 drum encoder, 8-27 drum heater, 8-27 drum temperature sensor, 8-27 exit module, 8-30 I/O and electronic, 3-25 IDE hard drive, 2-19 ink loader, 8-7 media drive motor, 8-30 pick solenoid, 8-41 power cord parts list, 9-16 printhead power, 3-14 ribbon connector, 8-5 serial modem, 4-73 USB, 4-72 wave amp, 3-40 cabling, parts list, 9-13 calibration faults, 3-33, 3-35 cancel button, 1-5 chase page, 2-34, 4-3, 4-55 check menu tables, 4-10 check activators menu, 4-10 deskew clutch, 4-11 drum heater relay, 4-12 head maintenance clutch, 4-10 purge vent solenoid, 4-12 strip solenoid, 4-12 tray 1 pick solenoid, 4-11 tray 2, tray 3, tray 4, pick clutch, 4-11 check drive menu, 4-31 drum maintenance drive, 4-34 paper path drive, 4-32 tilt drive, 4-35 transfix drive slow and transfix drive fast, 4-34 tray 2, tray 3, tray 4, lift plate drive, 4-36 wiper drive, 4-31 x-axis drive, 4-33 check drum menu, 4-37 drum maintenance contact, 4-42 stripper contact, 4-41 y-axis belt slip, 4-40 y-axis belt tension, 4-40 y-axis drive, 4-39 y-axis encoder, 4-37 y-axis geometry, 4-38 check misc menu, 4-46 drum maint/transfix home, 4-50 paper path status, 4-46 purge pump, 4-47 temperature status, 4-47 voltages, 4-49 wiper alignment, 4-49 check motors menu, 4-43 media path motor, 4-44 process motor, 4-44 tray 2, tray 3, tray 4, lift motor, 4-45 tray 3 and tray 4 pick/feed motor, 4-45 x-axis motor, 4-43 y-axis motor, 4-43 check paper path menu duplex paper drive power, 4-27 duplex paper lead edge times, 4-28 duplex paper sensor bounce times, 4-30 duplex paper trail edge times, 4-29 paper drive power, 4-22 paper lead edge times, 4-22 paper sensor bounce times, 4-26 paper trail edge times, 4-24 tray 1 pick shaft, 4-18 tray 2, tray 3, and tray 4 pick shaft, 4-20 wiper shaft, 4-16 check shafts menu, 4-13 deskew shaft, 4-13 cleaning ink smears, 7-3 light stripes or missing colors, 7-2 media jams, 7-3 Phaser 8400/8500/8550/8560 Color Printer Service Manual I - 1