Icom IC-2820H Instruction Manual - Page 114
Code programming
View all Icom IC-2820H manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 114 highlights
12 PAGER/CODE SQUELCH D Code programming Your ID code MUST be programmed into code channel C0. Up to 5 transmit codes (codes that you transmit) are programmable into code channels, C1 to C5, if required. q Push [F• ] to display the function guide. w Push [MENU](V/MHz•SCAN) (Right band's) to enter MENU screen. e Rotate [DIAL] to select "DUP/TONE..." then push [MAIN•BAND]. r Rotate [DIAL] to select "PGR MEMORY", then push the [MAIN•BAND]. t Rotate [DIAL] to select code channel C0. • "C0" is your ID code and "C1" to "C5" are transmit codes. • Each transceiver should have a different ID code. y Push [MAIN•BAND] to select the pager code programming condition. u Rotate [DIAL] to select number (0-9) and push [>](M/CALL•MW) (Left band's) or [
93
12
PAGER/CODE SQUELCH
D
Code programming
Your ID code
MUST
be programmed into code channel C0.
Up to 5 transmit codes (codes that you transmit) are pro-
grammable into code channels, C1 to C5, if required.
q
Push
[
F
•
]
to display the function guide.
w
Push
[MENU](V/MHz•SCAN)
(Right band’s)
to enter MENU
screen.
e
Rotate
[DIAL]
to select “DUP/TONE…” then push
[MAIN•BAND]
.
r
Rotate
[DIAL]
to select “PGR MEMORY”, then push the
[MAIN•BAND]
.
t
Rotate
[DIAL]
to select code channel C0.
• “C0” is your ID code and “C1” to “C5” are transmit codes.
• Each transceiver should have a different ID code.
y
Push
[MAIN•BAND]
to select the pager code program-
ming condition.
u
Rotate
[DIAL]
to select number (0–9) and push
[>](M/CALL•MW)
(Left band’s)
or
[<](V/MHz•SCAN)
(Left
band’s)
to select the digit.
i
Repeat the step
u
to enter the desired 3-digit ID code,
then push
[MAIN•BAND]
.
o
Rotate
[DIAL]
to select a transmit code channel from C1 to
C5, then push the
[MAIN•BAND]
.
!
0
Enter the desired 3-digit transmit code as described in
steps
u
and
i
.
!
1
Push
[SKIP](V/MHz•SCAN)
(Left band’s)
to set the channel
to “receive inhibit” or “receive accept” ON and OFF.
• When “receive inhibit” is set, “SKIP” appears.
• Code channel C0 cannot be set as “receive inhibit.”
• See the table for “receive accept” and “receive inhibit” details
on the previous page.
!
2
Repeat steps
o
and
!
1
to set additional transmit code
channels, if desired.
!
3
Push
[BACK](V/MHz•SCAN)
(Right band’s)
twice to return
to frequency indication.
• Receive accept/receive inhibit
➥
“Receive accept”
(no “SKIP” indication)
accepts pager calls
when the transceiver receives a signal with a code the
same as that in the code channel.
➥
“Receive inhibit”
(“SKIP” appears)
ignores calls even when
the transceiver receives a code that is the same as the
code in the code channel. Transmit codes should there-
fore be programmed for “receive inhibit,” otherwise the
transceiver will not reject unnecessary calls.