Icom IC-2820H Instruction Manual - Page 87

Programming memory/bank/scan name

Get Icom IC-2820H PDF manuals and user guides View all Icom IC-2820H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

6 MEMORY MODE OPERATION ■ Programming memory/bank/scan name 1 Each memory channel can be programmed with an alphanumeric channel name for easy recognition and can be indicated independently by channel. Names can be a maximum of 8 characters- see the following table for available characters. q Select the desired memory channel to be programmed. ➥ Push [M/CALL•MW] several times to select memory mode, then rotate the same band's [DIAL] to select the desired memory channel. wPush and hold the same band's [M/CALL•MW] for 1 sec. to enter select memory write mode. • "X" indicator and the memory channel number blink. ePush [SEL](V/MHz•SCAN) (Left band's) several times to select programming the name conditions. "BANK" : The memory bank "B NAME" : The bank name (appears only when the selected memory bank is edited into a bank) "M NAME" : The memory name "S NAME" : The scan name (appears only when a scan edge channel is selected) • Frequency readouts disappear. r Push [EDIT](M/CALL•MW) (Right band's) to edit. • "X" indicator and cursor blinks. tRotate the same band's [DIAL] to select the desired character. • The selected character blinks. • Push [Aa](TONE•DTMF) to select the character group from cap- ital letter characters or lower case letters. • Push [1/](M/CALL•MW) (Right band's) to select the character 2 group from numbers or symbols. • Push [>](M/CALL•MW) (Left band's) to move the cursor right; 3 push [

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
66
6
MEMORY MODE OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
■
Programming memory/bank/scan name
Each memory channel can be programmed with an alphanu-
meric channel name for easy recognition and can be indi-
cated independently by channel. Names can be a maximum
of 8 characters— see the following table for available char-
acters.
q
Select the desired memory channel to be programmed.
➥
Push
[M/CALL•MW]
several times to select memory
mode, then rotate the same band’s
[DIAL]
to select the
desired memory channel.
w
Push and hold the same band’s
[M/CALL•MW]
for 1 sec.
to enter select memory write mode.
•“
X
” indicator and the memory channel number blink.
e
Push
[SEL](V/MHz•SCAN)
(Left band’s)
several times to se-
lect programming the name conditions.
“BANK”
: The memory bank
“B NAME”
: The bank name
(appears only when the selected
memory bank is edited into a bank)
“M NAME” : The memory name
“S NAME”
: The scan name
(appears only when a scan edge
channel is selected)
• Frequency readouts disappear.
r
Push
[EDIT](M/CALL•MW)
(Right band’s)
to edit.
•“
X
” indicator and cursor blinks.
t
Rotate the same band’s
[DIAL]
to select the desired char-
acter.
• The selected character blinks.
• Push
[Aa](TONE•DTMF)
to select the character group from cap-
ital letter characters or lower case letters.
• Push
[1/](M/CALL•MW)
(Right band’s)
to select the character
group from numbers or symbols.
• Push
[>](M/CALL•MW)
(Left band’s)
to move the cursor right;
push
[<](V/MHz•SCAN)
(Left band’s) to move the cursor left.
• Push
[CLR](DUP/MONI)
to clear the selected character.
• Push and hold
[CLR](DUP/MONI)
for 1 sec. to clear all charac-
ters after the selected character.
y
Repeat steps
e
and
t
until the desired channel name is
programmed.
u
Push
[BACK](V/MHz•SCAN)
(Right band’s)
to set the name.
i
Push and hold
[S.MW](M/CALL•MW)
(Right band’s)
for
1 sec. to overwrite the memory channel to store the mem-
ory name.
NOTE:
Only one bank name can be programmed into
each bank. Therefore, the previously programmed bank
name will be displayed when bank name indication is se-
lected. Also, the programmed bank name is assigned for
the other bank channels automatically.
D
Available characters
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
0123456789
(Space)
!''#$%&'()*+,-
./:;<=>?@[\]^_`{|}
~