Kyocera TASKalfa 4500i KM-NET Viewer Operation Guide Rev-5.2-2011-3 - Page 71

Communication Timeout, SNMP Communication Retries, Secure Protocol Settings, Login Settings, Device

Get Kyocera TASKalfa 4500i PDF manuals and user guides View all Kyocera TASKalfa 4500i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

2. Click Device > Device Home Page in the menu bar. 3. Login to the device from the Command Center, and click the Advanced tab at the top of the page. 4. To the left of the page, under Protocols, select TCP/IP and then select Logical Printers. The TCP/IP port is displayed for each logical printer. One of these logical printer ports must match the port number entered in Communication Settings. A restart may be required for logical printer changes to take effect. Use the Reset page in the Command Center Basic tab. Note: In older models, set the port number from the device home page. Select Networking > Logical Printers. To restart, select General > Reset. Communication Timeout Enter the number of seconds the server should wait for the printing device to respond to an SNMP or SOAP request. The available range is from 5 to 120 seconds. SNMP Communication Retries Enter the number of times, after an initial failure, the application should attempt to establish SNMP communication with the printing device. The available range is from 0 to 5 retries. A higher number will increase network traffic, while a lower number can improve performance. Secure Protocol Settings Secure Sockets Layer (SSL) is a cryptographic protocol that provides security for network communications. SSL support varies by network interface model. Select SSL to use HTTPS for device communication. Clear SSL to use HTTP for device communication. Login Settings The Login section lets you set user login information. The feature can be set if at least one selected device supports the User Login feature. KMnet Viewer 5.2 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
KMnet Viewer
5.2
62
2. Click
Device
>
Device Home Page
in the menu bar.
3.
Login to the device from the Command Center, and click the
Advanced
tab at the top of the page.
4.
To the left of the page, under
Protocols
, select
TCP/IP
and
then select
Logical Printers
. The
TCP/IP
port is displayed
for each logical printer. One of these logical printer ports
must match the port number entered in
Communication
Settings
.
A restart may be required for logical printer changes to take effect.
Use the
Reset
page in the Command Center
Basic
tab.
Note:
In older models, set the port number from the device home
page. Select
Networking
>
Logical Printers
. To restart, select
General
>
Reset
.
Communication Timeout
Enter the number of seconds the server should wait for the printing
device to respond to an SNMP or SOAP request. The available
range is from 5 to 120 seconds.
SNMP Communication Retries
Enter the number of times, after an initial failure, the application
should attempt to establish SNMP communication with the printing
device. The available range is from 0 to 5 retries. A higher number
will increase network traffic, while a lower number can improve
performance.
Secure Protocol Settings
Secure Sockets Layer (
SSL
) is a cryptographic protocol that provides
security for network communications.
SSL
support varies by network
interface model.
Select
SSL
to use
HTTPS
for device communication.
Clear
SSL
to use
HTTP
for device communication.
Login Settings
The Login section lets you set user login information. The feature can
be set if at least one selected device supports the User Login feature.