Home » Cisco Manuals » Bridges & Routers » Cisco SR224T » Manual Viewer

Cisco SR224T Administration Guide - Page 134

Smartport Interface Settings

Add to My Manuals
Save this manual to your list of manuals

Page 134 highlights

Smartports Configuring Smartport Using The Web-based Interface 10 STEP 5 Click Apply to save the changes to the running configuration. If the Smartport macro and/or its parameter values associated with the Smartport type are modified, Auto Smartport automatically reapplies the macro to the interfaces currently assigned with the Smartport type by Auto Smartport. Auto Smartport does not apply the changes to interfaces that were statically assigned a Smartport type. NOTE There is no method to validate macro parameters because they do not have a type association. Therefore, any entry is valid at this point. However, invalid parameter values may cause errors to occur when the Smartport type is assigned to an interface, applying the associated macro. Smartport Interface Settings Use the Interface Settings page to perform the following tasks: • Statically apply a specific Smartport type to an interface with interface specific values for the macro parameters. • Enable Auto Smartport on an interface. • Diagnose a Smartport macro that failed upon application, and caused the Smartport type to become Unknown. • Reapply a Smartport macro after it fails for one of the following types of interfaces: switch, router and AP. It is expected that the necessary corrections have been made prior to clicking Reapply. See the workflow area in Common Smartport Tasks section for troubleshooting tips. • Reapply a Smartport macro to an interface. In some circumstances, you may want to reapply a Smartport macro so that the configuration at an interface is up to date. For instance, reapplying a switch Smartport macro at a switch interface makes the interface a member of the VLANs created since the last macro application. You have to be familiar with the current configurations on the switch and the definition of the macro to determine if a reapplication has any impact on the interface. • Reset unknown interfaces. This sets the mode of Unknown interfaces to Default. Cisco Small Business 200 Series Smart Switch Administration Guide 135

Section	Page
Getting Started	7
Starting the Web-based Switch Configuration Utility	7
Quick Start Switch Configuration	11
Interface Naming Conventions	11
Window Navigation	13
Viewing Statistics	17
Viewing Ethernet Interfaces	17
Viewing Etherlike Statistics	18
Viewing 802.1X EAP Statistics	19
Managing RMON	21
Managing System Logs	24
Setting System Log Settings	24
Setting Remote Logging Settings	26
Viewing Memory Logs	27
Managing System Files	29
Types of System Files	29
Upgrade/Backup Firmware/Language	32
Downloading or Backing-up a Configuration or Log	34
Viewing Configuration Files Properties	37
Copying Configuration Files	38
DHCP Auto Configuration	39
General Administrative Information	43
Switch Models	43
System Information	45
Rebooting the Switch	47
Monitoring the Fan Status and Temperature	48
Defining Idle Session Timeout	48
Pinging a Host	49
System Time	51
System Time Options	52
SNTP Modes	53
Configuring System Time	54
Managing Device Diagnostics	61
Testing Copper Ports	61
Displaying Optical Module Status	63
Configuring Port and VLAN Mirroring	64
Viewing CPU Utilization and Secure Core Technology	66
Configuring Discovery	68
Configuring Bonjour Discovery	68
LLDP and CDP	69
Configuring LLDP	70
Configuring CDP	91
Port Management	100
Configuring Ports	100
Setting Basic Port Configuration	101
Configuring Link Aggregation	103
Configuring Green Ethernet	111
Smartports	118
Overview	118
What is a Smartport	119
Smartport Types	119
Smartport Macros	122
Macro Failure and the Reset Operation	123
How the Smartport Feature Works	124
Auto Smartport	124
Error Handling	128
Default Configuration	128
Relationships with Other Features and Backwards Compatibility	129
Common Smartport Tasks	129
Configuring Smartport Using The Web-based Interface	131
Built-in Smartport Macros	136
Managing Power-over-Ethernet Devices	148
PoE on the Switch	148
Configuring PoE Properties	151
Configuring the PoE Power, Priority, and Class	152
VLAN Management	155
VLANs	155
Configuring Default VLAN Settings	158
Creating VLANs	159
Configuring VLAN Interface Settings	160
Defining VLAN Membership	161
Voice VLAN	165
Configuring the Spanning Tree Protocol	179
STP Flavors	179
Configuring STP Status and Global Settings	180
Defining Spanning Tree Interface Settings	182
Configuring Rapid Spanning Tree Settings	184
Managing MAC Address Tables	187
Configuring Static MAC Addresses	188
Managing Dynamic MAC Addresses	188
Configuring Multicast Forwarding	190
Multicast Forwarding	190
Defining Multicast Properties	193
Adding MAC Group Address	195
Adding IP Multicast Group Addresses	197
Configuring IGMP Snooping	198
MLD Snooping	200
Querying IGMP/MLD IP Multicast Group	203
Defining Multicast Router Ports	204
Defining Forward All Multicast	205
Defining Unregistered Multicast Settings	206
Configuring IP Information	207
Management and IP Interfaces	207
Configuring ARP	219
Domain Name Systems	220
Configuring Security	224
Defining Users	225
Configuring RADIUS	228
Configuring Management Access Authentication	230
Defining Management Access Method	231
Configuring TCP/UDP Services	236
Defining Storm Control	237
Configuring Port Security	238
Configuring 802.1X	241
Denial of Service Prevention	247
Using the SSL Feature	249
SSL Overview	249
Default Settings and Configuration	249
SSL Server Authentication Settings	250
Secure Sensitive Data	252
Introduction	252
SSD Rules	253
SSD Properties	258
Configuration Files	261
SSD Management Channels	266
Menu CLI and Password Recovery	266
Configuring SSD	267
Configuring Quality of Service	270
QoS Features and Components	271
Configuring QoS - General	272

Match case Limit results 1 per page

Smartports

Configuring Smartport Using The Web-based Interface

Cisco Small Business 200 Series Smart Switch Administration Guide

135

STEP

Click

Apply

to save the changes to the running configuration. If the Smartport

macro and/or its parameter values associated with the Smartport type are

modified, Auto Smartport automatically reapplies the macro to the interfaces

currently assigned with the Smartport type by Auto Smartport.

Auto Smartport

does not apply the changes to interfaces that were statically assigned a

Smartport type.

NOTE

There is no method to validate macro parameters because they do not have a type

association. Therefore, any entry is valid at this point. However, invalid parameter

values may cause errors to occur when the Smartport type is assigned to an

interface, applying the associated macro.

Smartport Interface Settings

Use the

Interface Settings

page to perform the following tasks:

•

Statically apply a specific Smartport type to an interface with interface

specific values for the macro parameters.

•

Enable Auto Smartport on an interface.

•

Diagnose a Smartport macro that failed upon application, and caused the

Smartport type to become Unknown.

•

Reapply a Smartport macro after it fails for one of the following types of

interfaces: switch, router and AP. It is expected that the necessary

corrections have been made prior to clicking

Reapply

. See the workflow

area in

Common Smartport Tasks

section for troubleshooting tips.

•

Reapply a Smartport macro to an interface.

In some circumstances, you

may want to reapply a Smartport macro so that the configuration at an

interface is up to date.

For instance, reapplying a switch Smartport macro

at a switch interface makes the interface a member of the VLANs created

since the last macro application.

You have to be familiar with the current

configurations on the switch and the definition of the macro to determine if a

reapplication has any impact on the interface.

•

Reset unknown interfaces. This sets the mode of Unknown interfaces to

Default.