Dell PowerEdge 4300 Dell PowerEdge 4300 Systems Installation and Troubleshooti - Page 139

tridge into the guide bracket assembly and firmly seat the assembly see

Get Dell PowerEdge 4300 PDF manuals and user guides View all Dell PowerEdge 4300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 139 highlights

retention pins (2) SEC cartridge SEC cartridge release latches (2) heat sink guide bracket assembly Use the following procedure to install the replacement SEC cartridge and heat sink assembly: 1. Remove the terminator card or old SEC cartridge from the guide bracket assembly. Follow the instructions in "Removing a Terminator Card" or "Removing the SEC Cartridge and Heat Sink Assembly" found earlier in this chapter, as appropriate. 2. With the heat sink facing the other microprocessor socket, slide the SEC cartridge into the guide bracket assembly and firmly seat the assembly (see Figure 8-11). 3. Reinstall the two retention pins to secure the SEC cartridge and heat sink assembly. 4. Verify that the cartridge release latches on the guide bracket assembly are pulled out. Installing System Board Options 8-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
Installing System Board Options
8-15
)LJXUH±½¶´¿µ±±5HPRYLQJ±DQ±6(&±&DUWULGJH±DQG±+HDW±6LQN±$VVHPEO\
5HSODFLQJ±WKH±6(&±&DUWULGJH±DQG±+HDW±6LQN±$VVHPEO\
Use the following procedure to install the replacement SEC cartridge and heat sink
assembly:
1.
Remove the terminator card or old SEC cartridge from the guide bracket
assembly.
Follow the instructions in “Removing a Terminator Card” or “Removing the SEC
Cartridge and Heat Sink Assembly” found earlier in this chapter, as appropriate.
2.
With the heat sink facing the other microprocessor socket, slide the SEC car-
tridge into the guide bracket assembly and firmly seat the assembly (see
Figure 8-11).
3.
Reinstall the two retention pins to secure the SEC cartridge and heat sink
assembly.
4.
Verify that the cartridge release latches on the guide bracket assembly are pulled
out.
SEC cartridge
release latches (2)
heat sink
SEC cartridge
retention pins (2)
guide bracket
assembly