HP Latex 110 Users Guide - Page 133

Clean the exterior of the printer, Move or store the printer, WARNING, CAUTION

Get HP Latex 110 PDF manuals and user guides View all HP Latex 110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 133 highlights

8. Use the damp cloth to remove remaining dry ink deposits. 9. Close the 95% ethanol container and remove it and the cloth from the vicinity of the printer. 10. Wait 3 or 4 minutes to let the ethanol evaporate, before turning on the printer and reloading the substrate. 11. With a 1 mm diameter pin ensure that the vacuum holes are not obstructed, especially the holes that are covered by the most-used substrate sizes. Clean the exterior of the printer Use a damp sponge or a soft cloth and a mild household cleaner such as non-abrasive liquid soap to clean the outside of the printer and all other parts of the printer that you regularly touch as part of normal operation. There may be some dampness from condensation under the fans of the curing module, which should be wiped with a dry cloth. WARNING! To avoid an electric shock, make sure that the printer is turned off and unplugged before you clean it. Do not let water get inside the printer. CAUTION: Do not use abrasive cleaners on the printer. Move or store the printer If you need to move your printer or store it for an extended period of time, prepare it correctly to avoid possible damage. 1. Do not remove the ink cartridges, printheads or maintenance cartridge. 2. Make sure that no substrate is loaded. 3. Make sure that the printhead carriage is located in the service station (at the right end of the printer). 4. Make sure that the Ready message appears on the front panel. 5. Turn off the power by using the Power button on the front panel. 6. Also switch off the power switch at the rear of the printer. 7. Disconnect any cables that connect the printer to a network, a computer, or a scanner. 8. If you intend to turn the printer upside down or on its side, first remove the maintenance cartridge (see Replace the maintenance cartridge on page 119). 9. For correct environmental storage conditions, see Environmental specifications on page 145. ENWW Clean the exterior of the printer 127

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
8.
Use the damp cloth to remove remaining dry ink deposits.
9.
Close the 95% ethanol container and remove it and the cloth from the vicinity of the printer.
10.
Wait 3 or 4 minutes to let the ethanol evaporate, before turning on the printer and reloading the
substrate.
11.
With a 1 mm diameter pin ensure that the vacuum holes are not obstructed, especially the holes that
are covered by the most-used substrate sizes.
Clean the exterior of the printer
Use a damp sponge or a soft cloth and a mild household cleaner such as non-abrasive liquid soap to clean the
outside of the printer and all other parts of the printer that you regularly touch as part of normal operation.
There may be some dampness from condensation under the fans of the curing module, which should be
wiped with a dry cloth.
WARNING!
To avoid an electric shock, make sure that the printer is turned off and unplugged before you
clean it. Do not let water get inside the printer.
CAUTION:
Do not use abrasive cleaners on the printer.
Move or store the printer
If you need to move your printer or store it for an extended period of time, prepare it correctly to avoid
possible damage.
1.
Do not remove the ink cartridges, printheads or maintenance cartridge.
2.
Make sure that no substrate is loaded.
3.
Make sure that the printhead carriage is located in the service station (at the right end of the printer).
4.
Make sure that the
Ready
message appears on the front panel.
5.
Turn off the power by using the
Power
button on the front panel.
6.
Also switch off the power switch at the rear of the printer.
7.
Disconnect any cables that connect the printer to a network, a computer, or a scanner.
8.
If you intend to turn the printer upside down or on its side, first remove the maintenance cartridge (see
Replace the maintenance cartridge
on page
119
).
9.
For correct environmental storage conditions, see
Environmental specifications
on page
145
.
ENWW
Clean the exterior of the printer
127