HP Latex 110 Users Guide - Page 57

The edge holders

Get HP Latex 110 PDF manuals and user guides View all HP Latex 110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

5. Once the substrate is correctly fed into the printer, pull down the substrate pinch lever as far as it will go. 6. Select the category and name of the substrate you are loading. The rest of the assisted load procedure is the same as in the normal load procedure. See Load a roll into the printer on page 46. The edge holders The edge holders are designed to prevent the edges of the substrate from rising while printing is in progress. They are not normally necessary. When not in use, they should be stored inside the printer, to the left and right respectively, to avoid substrate jams. It is also a good idea to store the edge holders when no substrate is loaded, in case you later forget and leave them installed by mistake. NOTE: The edge holders extend 7 mm over the edge of the substrate. You should set a minimum left and right margin of 7 mm (0.3 in) in the RIP when using edge holders, otherwise the printer could try to print on the edge holders. If you choose to use them, you should move them into position when prompted by the front panel (this prompt appears when the Use edge holders checkbox has been checked). Open the window, place the edge holders, then close the window. The edge holders should be placed on the platen so that they slightly overlap the left and right edges of the substrate. There are marks on the printer to show where to place them. The edge holders for each printer model are the same, but they are installed in different ways. WARNING! Avoid moving parts. Handle fragile parts with care. You are recommended to wear gloves. ENWW The edge holders 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
5.
Once the substrate is correctly fed into the printer, pull down the substrate pinch lever as far as it will
go.
6.
Select the category and name of the substrate you are loading.
The rest of the assisted load procedure is the same as in the normal load procedure. See
Load a roll into the
printer
on page
46
.
The edge holders
The edge holders are designed to prevent the edges of the substrate from rising while printing is in progress.
They are not normally necessary. When not in use, they should be stored inside the printer, to the left and
right respectively, to avoid substrate jams. It is also a good idea to store the edge holders when no substrate
is loaded, in case you later forget and leave them installed by mistake.
NOTE:
The edge holders extend 7 mm over the edge of the substrate. You should set a minimum left and
right margin of 7 mm (0.3 in) in the RIP when using edge holders, otherwise the printer could try to print on
the edge holders.
If you choose to use them, you should move them into position when prompted by the front panel (this
prompt appears when the
Use edge holders
checkbox has been checked). Open the window, place the edge
holders, then close the window.
The edge holders should be placed on the platen so that they slightly overlap the left and right edges of the
substrate. There are marks on the printer to show where to place them.
The edge holders for each printer model are the same, but they are installed in different ways.
WARNING!
Avoid moving parts. Handle fragile parts with care. You are recommended to wear gloves.
ENWW
The edge holders
51