Home » HP Manuals » Printers » HP Latex 2700 » Manual Viewer

HP Latex 2700 User Guide 3 - Page 307

Movable Slot System sensor errors

$Get HP Latex 2700 PDF manuals and user guides$

Add to My Manuals
Save this manual to your list of manuals

Page 307 highlights

● Either the embedded spectrophotometer or the line sensor is not working properly. If the problem persists, call your service representative. Movable Slot System sensor errors If the printer fails to detect a change of position of the Movable Slot System (MSS) during a configuration change, a sensor has probably been damaged. Respond as follows: 1. Check that you are moving the MSS elements as directed by the Internal Print Server, or check the labels. 2. Run diagnostic 89004 (Movable Slot System sensors check) to find out which sensor is not working properly. 3. Call a service engineer as soon as possible to repair the sensor. To avoid leaving the printer idle because of a position sensor, there is a Skip step button in each step of the configuration change process. You can continue printing as follows: 1. Start the change of configuration. 2. Follow the instructions and move the elements as indicated in the Internal Print Server. 3. Identify the step in which the Internal Print Server does not detect a physical change of an MSS element. 4. Use the labels to verify that the element is where it should be. 5. Tap the Skip step button. You are warned to ensure that MSS elements are placed in the correct position for the selected configuration. CAUTION: If the printhead pocket and the capping station are not aligned, the printhead will be damaged. 6. Finish the process, after which the printer will be ready to print. 7. Remember to call a service engineer as soon as possible to repair the sensor. Major errors in the substrate-axis direction An error of more than 5 mm in the substrate-axis direction is regarded as major. These are the possibilities: ● The sensor is not working properly, and the printhead pocket is not positioned correctly. Proceed as follows: 1. Check that you are moving the MSS elements as directed by the Internal Print Server, or check the labels. 2. Run diagnostic 89004 (Movable Slot System sensors check) to find out which sensor is not working properly. 3. Call a service engineer as soon as possible to repair the sensor. ● The Skip step button has been used, and the printhead pocket is not positioned correctly. Proceed as follows: 1. Look at the labels to check whether the MSS elements have been positioned correctly. 2. Call a service engineer as soon as possible to repair the sensor. ● The positioning screw has not been tightened. Proceed as follows: 300 Chapter 16 Troubleshoot other issues

Section	Page
Introduction	8
Welcome to your printer	8
Printer accessories and consumables	9
Documentation and useful links	9
Safety precautions	10
Main components	20
Printer software	22
Turn on the printer for the first time	22
Turn the printer on and off	23
Move the printer	24
Printer status beacon	25
HP Internal Print Server	27
Start the Internal Print Server	27
Internal Print Server widgets	28
Printer status and alerts	29
Update the printer’s firmware and software (Internal Print Server)	30
Internal Print Server settings and preferences	34
RIP distribution	35
Install and configure the RIP software	36
Install ONYX software and set up the driver	36
Install Caldera software and set up the driver	38
Printing workflows integration	41
Introduction to JDF	41
Benefits of working with JDF for file submission	41
Creating JDF job tickets	41
What printer information can be communicated to an MIS?	42
How to integrate the printer into the Caldera RIP	42
How to integrate the printer into the Onyx RIP	42
Job submission methods	42
How to integrate the printer into an MIS system or production control software	43
Handle the substrate	44
Supported substrate types	44
Supported HP substrates	46
Substrate tips	47
Color consistency	48
Substrate configurations	49
Prepare to print	50
Substrate edge holders	51
Load a roll onto the spindle	53
Load a roll into the printer	55
Double-sided printing	63
Output-platen light	67
Consistency mode (optimize for tiling)	67
Optimize for ink consumption	68
Create and manage print jobs	70
Add a new print job	70
Substrate presets	72
Use a new substrate	72
Prepare the printer for a new substrate	72
Add a substrate preset	72
Online substrate manager	78
Edit a substrate preset	83
Remove a substrate preset	86
Export multiple presets	86
Job properties	86
Set the carriage beam position	88
Handle the ink system	90
Ink system components	90
How to work with ink system components	93
Printing with white ink (2700W only)	120
Printer calibration	132
Align the printheads	132
Possible difficulties with printhead alignment	138
Color calibration	139
Color consistency between different HP Latex 2700 series printers	141
Color profiles	141
Substrate-advance compensation	141
Calibrations specific to one substrate preset	146
Recommended calibrations after particular events	146
Accessories	147
Accessory compatibility	147
Spindle	147
Dual-roll printing	148
Jumbo dual-roll kit	150
Diverter roller	151
In-line slitters	152
Substrate saver	154
Ink collector	159
Roll to free fall	164
Roll to collector	164
Hardware maintenance	166
Safety precautions	166
Maintenance resources	166
Summary of maintenance operations	168
How to perform maintenance operations	169
Diagnostics	266
Troubleshoot substrate issues	269
Substrate cannot be loaded successfully	269
Substrate has jammed	269
Substrate is not attached to the core and/or spindle	270
Substrate is not flat	271
Spindle latch suddenly opens during printer operation	271
Substrate advances with a loud continuous sound of vibration	271
There is skew or telescoping on the output spindle	272
There are wrinkles and ink smears on the substrate	273
There are ink marks on the substrate	276
Substrate sticks to the platen	276
There are physical marks on the substrate	277
There are drops of ink on the substrate	278
Print is shorter than expected	279
How to achieve better consistency between jobs of the same length	279
Collector stops winding	280
Collector occasionally fails to work correctly	280
Collector winds in the wrong direction	281
Substrate is detached or winds around the collector in the wrong direction	281
There is skew or telescoping on the collector	281
Substrate has jammed on the collector	281
Troubleshoot print-quality issues	282
General advice	282
Basic and advanced troubleshooting	283
Troubleshoot ink cartridge and printhead issues	298
Ink cartridges	298
Printheads	299
Printhead cleaning roll errors	304
Troubleshoot other issues	305
Printer does not start	305
Printer does not print	305
Printer cannot be restarted from the Internal Print Server	305
Printer seems slow	306
Request to reinitialize the carriage	306
Internal Print Server cannot detect the printer	306
Color calibration fails	306
Movable Slot System sensor errors	307
When you need help	309
HP Customer Care	309
HP PrintOS: the cloud-based platform for print specialists	309
Printer specifications	330
Functional specifications	330
Physical specifications	331
Memory specifications	332
Power specifications	332
Air supply requirements (pneumatic spindle)	332
Environmental specifications	333
Acoustic specifications	333
Flexible substrate recommendations	335
Predefined substrate settings	335
Self-adhesive vinyls	335
PVC banners	336
Papers	336
Textiles	337
Flexible films	337
Print-quality-troubleshooting summary table	339
Glossary	340

Match case Limit results 1 per page

●

Either the embedded spectrophotometer or the line sensor is not working properly. If the problem persists,

call your service representative.

Movable Slot System sensor errors

If the printer fails to detect a change of position of the Movable Slot System (MSS) during a conﬁguration change,

a sensor has probably been damaged.

Respond as follows:

Check that you are moving the MSS elements as directed by the Internal Print Server, or check the labels.

Run diagnostic 89004 (Movable Slot System sensors check) to ﬁnd out which sensor is not working properly.

Call a service engineer as soon as possible to repair the sensor.

To avoid leaving the printer idle because of a position sensor, there is a

Skip step

button in each step of the

conﬁguration change process. You can continue printing as follows:

Start the change of conﬁguration.

Follow the instructions and move the elements as indicated in the Internal Print Server.

Identify the step in which the Internal Print Server does not detect a physical change of an MSS element.

Use the labels to verify that the element is where it should be.

Tap the

Skip step

button. You are warned to ensure that MSS elements are placed in the correct position for

the selected conﬁguration.

CAUTION:

If the printhead pocket and the capping station are not aligned, the printhead will be damaged.

Finish the process, after which the printer will be ready to print.

Remember to call a service engineer as soon as possible to repair the sensor.

Major errors in the substrate-axis direction

An error of more than 5 mm in the substrate-axis direction is regarded as major.

These are the possibilities:

●

The sensor is not working properly, and the printhead pocket is not positioned correctly. Proceed as follows:

Check that you are moving the MSS elements as directed by the Internal Print Server, or check the labels.

Run diagnostic 89004 (Movable Slot System sensors check) to ﬁnd out which sensor is not working

properly.

Call a service engineer as soon as possible to repair the sensor.

●

The Skip step button has been used, and the printhead pocket is not positioned correctly. Proceed as follows:

Look at the labels to check whether the MSS elements have been positioned correctly.

Call a service engineer as soon as possible to repair the sensor.

●

The positioning screw has not been tightened. Proceed as follows:

300

Chapter 16

Troubleshoot other issues