Yamaha 01V96i Reference Manual - Page 104

Assigning Parameters to Control Changes for Real-time Control, Press the DISPLAY ACCESS [MIDI] button

Get Yamaha 01V96i PDF manuals and user guides View all Yamaha 01V96i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

104 MIDI Assigning Parameters to Control Changes for Real-time Control You can assign 01V96i parameters to MIDI Control Changes for real-time control. When the 01V96i receives a Control Change, the assigned 01V96i parameter is set accordingly. Also, when you adjust a parameter on the 01V96i, the 01V96i transmits the assigned Control Change message. Tip: You can store a Parameter to Control Change assignment table to an external device by using MIDI Bulk Dump or the Studio Manager software. 1. Press the DISPLAY ACCESS [DIO/SETUP] but- ton repeatedly until the DIO/Setup | MIDI/Host page appears, then specify ports for transmission and reception of MIDI messages (see page 101). 2. Make connections using the ports selected in Step 1 so that the 01V96i can transfer MIDI messages to and from the external device. 3. Press the DISPLAY ACCESS [MIDI] button, then press the [F3] button. The MIDI | Ctl Asgn page appears. This page enables you to assign 01V96i parameters to Control Changes. 1 Tip: See page 157 for information on the default Parameter to Control Change assignments. 4. Move the cursor to the MODE parameter's TABLE button (1), then press [ENTER]. The MODE parameter determines which MIDI messages are transmitted when 01V96i parameters are adjusted. The following options are available for the MODE parameter: • TABLE MIDI Control Change messages are transmitted in accordance with the assignments on this page. • NRPN The assignments on the Ctl Asgn page are ignored, and predefined NRPNs (Non Registered Parameter Numbers) are transmitted for remote control. Tip: NRPNs are special MIDI messages that combine three different Control Changes. They enable you to control many parameters on a single MIDI Channel. 5. If you turned on the TABLE button in Step 4, move the cursor to a parameter box in the No. (CH) column, then rotate the Parameter wheel or press the [INC]/[DEC] buttons to select the MIDI channels and Control Changes to which you want to assign parameters. You can assign parameters to up to 16-channel Control Changes on the Ctl Asgn page, regardless of the MIDI Channels currently selected for transmission and reception. Skip Steps 5 and 6 if you turned on the NRPN button in Step 4. 6. Select parameters in the parameter boxes in the three PARAMETER columns. Select a parameter group in the parameter box in the first PARAMETER column, and specify the desired values in the parameter boxes in the second and third PARAMETER columns. The following parameters and values are available: HIGH MID LOW NO ASSIGN - - CHANNEL INPUT1-32/ST IN1-4 MASTER BUS1-8/AUX1-8/STEREO AUX1 SEND AUX2 SEND AUX3 SEND FADER H AUX4 SEND INPUT1-32/ST IN1-4 AUX5 SEND AUX6 SEND AUX7 SEND AUX8 SEND BUS TO ST BUS1-8 CHANNEL INPUT1-32/ST IN1-4 MASTER BUS1-8/AUX1-8/STEREO AUX1 SEND AUX2 SEND AUX3 SEND FADER L AUX4 SEND INPUT1-32/ST IN1-4 AUX5 SEND AUX6 SEND AUX7 SEND AUX8 SEND BUS TO ST BUS1-8 01V96i-Reference Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
104
MIDI
01V96i—Reference Manual
Assigning Parameters to
Control Changes for
Real-time Control
You can assign 01V96i parameters to MIDI Control Changes
for real-time control. When the 01V96i receives a Control
Change, the assigned 01V96i parameter is set accordingly.
Also, when you adjust a parameter on the 01V96i, the 01V96i
transmits the assigned Control Change message.
1.
Press the DISPLAY ACCESS [DIO/SETUP] but-
ton repeatedly until the DIO/Setup |
MIDI/Host page appears, then specify ports
for transmission and reception of MIDI mes-
sages (see page 101).
2.
Make connections using the ports selected in
Step 1 so that the 01V96i can transfer MIDI
messages to and from the external device.
3.
Press the DISPLAY ACCESS [MIDI] button,
then press the [F3] button.
The MIDI | Ctl Asgn page appears. This page enables you
to assign 01V96i parameters to Control Changes.
4.
Move the cursor to the MODE parameter’s
TABLE button (
1
), then press [ENTER].
The MODE parameter determines which MIDI messages
are transmitted when 01V96i parameters are adjusted.
The following options are available for the MODE
parameter:
• TABLE
MIDI Control Change messages are transmitted in accor-
dance with the assignments on this page.
• NRPN
The assignments on the Ctl Asgn page are ignored, and
predefined NRPNs (Non Registered Parameter Num-
bers) are transmitted for remote control.
5.
If you turned on the TABLE button in Step 4,
move the cursor to a parameter box in the No.
(CH) column, then rotate the Parameter
wheel or press the [INC]/[DEC] buttons to
select the MIDI channels and Control
Changes to which you want to assign param-
eters.
You can assign parameters to up to 16-channel Control
Changes on the Ctl Asgn page, regardless of the MIDI
Channels currently selected for transmission and recep-
tion.
Skip Steps 5 and 6 if you turned on the NRPN button in
Step 4.
6.
Select parameters in the parameter boxes in
the three PARAMETER columns.
Select a parameter group in the parameter box in the first
PARAMETER column, and specify the desired values in
the parameter boxes in the second and third PARAME-
TER columns.
The following parameters and values are available:
Tip:
You can store a Parameter to Control Change assignment
table to an external device by using MIDI Bulk Dump or the Stu-
dio Manager software.
Tip:
See page 157 for information on the default Parameter
to Control Change assignments.
1
Tip:
NRPNs are special MIDI messages that combine three
different Control Changes. They enable you to control many
parameters on a single MIDI Channel.
HIGH
MID
LOW
NO ASSIGN
—
—
FADER H
CHANNEL
INPUT1–32/ST IN1–4
MASTER
BUS1–8/AUX1–8/STEREO
AUX1 SEND
INPUT1–32/ST IN1–4
AUX2 SEND
AUX3 SEND
AUX4 SEND
AUX5 SEND
AUX6 SEND
AUX7 SEND
AUX8 SEND
BUS TO ST
BUS1–8
FADER L
CHANNEL
INPUT1–32/ST IN1–4
MASTER
BUS1–8/AUX1–8/STEREO
AUX1 SEND
INPUT1–32/ST IN1–4
AUX2 SEND
AUX3 SEND
AUX4 SEND
AUX5 SEND
AUX6 SEND
AUX7 SEND
AUX8 SEND
BUS TO ST
BUS1–8