Yamaha 01V96i Reference Manual - Page 137

DYNA. PHASER, REV+CHORUS, REV->CHORUS, REV+FLANGE, Two input, two output dynamically controlled

Get Yamaha 01V96i PDF manuals and user guides View all Yamaha 01V96i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 137 highlights

Appendix: Parameter Lists Effects Parameters 137 DYNA. PHASER Two input, two output dynamically controlled phaser. Parameter Range SOURCE INPUT, MIDI SENSE 0-100 DIR. UP, DOWN DECAY 1 OFFSET 0-100 FB.GAIN -99 to +99% STAGE LSH F LSH G HSH F HSH G 2, 4, 6, 8, 10, 12, 14, 16 21.2 Hz-8.00 kHz -12.0 to +12.0 dB 50.0 Hz-16.0 kHz -12.0 to +12.0 dB Description Control source: input signal or MIDI Note On velocity Sensitivity Upward or downward frequency change Decay speed Lowest phase-shifted frequency offset Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) Number of phase shift stages Low shelving filter frequency Low shelving filter gain High shelving filter frequency High shelving filter gain 1. 6 ms-46.0 s (fs=44.1 kHz), 5 ms-42.3 s (fs=48 kHz), 3 ms-23.0 s (fs=88.2 kHz), 3 ms-21.1 s (fs=96 kHz) REV+CHORUS One input, two output reverb and chorus effects in parallel. Parameter Range REV TIME 0.3-99.0 s INI. DLY 0.0-500.0 ms HI. RATIO 0.1-1.0 DIFF. 0-10 DENSITY 0-100% HPF THRU, 21.2 Hz-8.00 kHz LPF 50.0 Hz-16.0 kHz, THRU REV/CHO 0-100% FREQ. 0.05-40.00 Hz AM DEPTH 0-100% PM DEPTH 0-100% MOD. DLY 0.0-500.0 ms WAVE Sine, Tri SYNC OFF, ON NOTE 1 Description Reverb time Initial delay before reverb begins High-frequency reverb time ratio Spread Reverb density High-pass filter cutoff frequency Low-pass filter cutoff frequency Reverb and chorus balance (0% = all reverb, 100% = all chorus) Modulation speed Amplitude modulation depth Pitch modulation depth Modulation delay time Modulation waveform Tempo parameter sync on/off Used in conjunction with TEMPO to determine FREQ. 1. REV->CHORUS One input, two output reverb and chorus effects in series. Parameter Range REV TIME 0.3-99.0 s INI. DLY 0.0-500.0 ms HI. RATIO 0.1-1.0 DIFF. 0-10 DENSITY 0-100% HPF THRU, 21.2 Hz-8.00 kHz LPF 50.0 Hz-16.0 kHz, THRU REV.BAL 0-100% FREQ. 0.05-40.00 Hz AM DEPTH 0-100% PM DEPTH 0-100% MOD. DLY 0.0-500.0 ms WAVE Sine, Tri SYNC OFF, ON NOTE 1 Description Reverb time Initial delay before reverb begins High-frequency reverb time ratio Spread Reverb density High-pass filter cutoff frequency Low-pass filter cutoff frequency Reverb and chorused reverb balance (0% = all chorused reverb, 100% = all reverb) Modulation speed Amplitude modulation depth Pitch modulation depth Modulation delay time Modulation waveform Tempo parameter sync on/off Used in conjunction with TEMPO to determine FREQ. 1. REV+FLANGE One input, two output reverb and flanger effects in parallel. Parameter REV TIME INI. DLY HI. RATIO DIFF. DENSITY HPF LPF REV/FLG FREQ. DEPTH MOD. DLY FB. GAIN WAVE SYNC NOTE Range 0.3-99.0 s 0.0-500.0 ms 0.1-1.0 0-10 0-100% THRU, 21.2 Hz-8.00 kHz 50.0 Hz-16.0 kHz, THRU 0-100% 0.05-40.00 Hz 0-100% 0.0-500.0 ms -99 to +99% Sine, Tri OFF, ON 1 Description Reverb time Initial delay before reverb begins High-frequency reverb time ratio Spread Reverb density High-pass filter cutoff frequency Low-pass filter cutoff frequency Reverb and flange balance (0% = all reverb, 100% = all flange) Modulation speed Modulation depth Modulation delay time Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) Modulation waveform Tempo parameter sync on/off Used in conjunction with TEMPO to determine FREQ. 1. 01V96i-Reference Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Effects Parameters
137
Appendix: Parameter Lists
01V96i—Reference Manual
DYNA. PHASER
Two input, two output dynamically controlled
phaser.
REV+CHORUS
One input, two output reverb and chorus effects in
parallel.
REV->CHORUS
One input, two output reverb and chorus effects in
series.
REV+FLANGE
One input, two output reverb and flanger effects in
parallel.
Parameter
Range
Description
SOURCE
INPUT, MIDI
Control source: input signal or
MIDI Note On velocity
SENSE
0–100
Sensitivity
DIR.
UP, DOWN
Upward or downward fre-
quency change
DECAY
1
1.
6 ms–46.0 s (fs=44.1 kHz), 5 ms–42.3 s (fs=48 kHz), 3 ms–23.0 s
(fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)
Decay speed
OFFSET
0–100
Lowest phase-shifted frequency
offset
FB.GAIN
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feed-
back)
STAGE
2, 4, 6, 8, 10, 12,
14, 16
Number of phase shift stages
LSH F
21.2 Hz–8.00 kHz
Low shelving filter frequency
LSH G
–12.0 to +12.0 dB
Low shelving filter gain
HSH F
50.0 Hz–16.0 kHz
High shelving filter frequency
HSH G
–12.0 to +12.0 dB
High shelving filter gain
Parameter
Range
Description
REV TIME
0.3–99.0 s
Reverb time
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
HI. RATIO
0.1–1.0
High-frequency reverb time ratio
DIFF.
0–10
Spread
DENSITY
0–100%
Reverb density
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
REV/CHO
0–100%
Reverb and chorus balance (0%
= all reverb, 100% = all chorus)
FREQ.
0.05–40.00 Hz
Modulation speed
AM DEPTH
0–100%
Amplitude modulation depth
PM DEPTH
0–100%
Pitch modulation depth
MOD. DLY
0.0–500.0 ms
Modulation delay time
WAVE
Sine, Tri
Modulation waveform
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE
1
1.
Used in conjunction with TEMPO
to determine FREQ.
Parameter
Range
Description
REV TIME
0.3–99.0 s
Reverb time
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
HI. RATIO
0.1–1.0
High-frequency reverb time ratio
DIFF.
0–10
Spread
DENSITY
0–100%
Reverb density
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
REV.BAL
0–100%
Reverb and chorused reverb bal-
ance (0% = all chorused reverb,
100% = all reverb)
FREQ.
0.05–40.00 Hz
Modulation speed
AM DEPTH
0–100%
Amplitude modulation depth
PM DEPTH
0–100%
Pitch modulation depth
MOD. DLY
0.0–500.0 ms
Modulation delay time
WAVE
Sine, Tri
Modulation waveform
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE
1
1.
Used in conjunction with TEMPO
to determine FREQ.
Parameter
Range
Description
REV TIME
0.3–99.0 s
Reverb time
INI. DLY
0.0–500.0 ms
Initial delay before reverb begins
HI. RATIO
0.1–1.0
High-frequency reverb time ratio
DIFF.
0–10
Spread
DENSITY
0–100%
Reverb density
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
REV/FLG
0–100%
Reverb and flange balance (0% =
all reverb, 100% = all flange)
FREQ.
0.05–40.00 Hz
Modulation speed
DEPTH
0–100%
Modulation depth
MOD. DLY
0.0–500.0 ms
Modulation delay time
FB. GAIN
–99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feed-
back)
WAVE
Sine, Tri
Modulation waveform
SYNC
OFF, ON
Tempo parameter sync on/off
NOTE
1
1.
Used in conjunction with TEMPO
to determine FREQ.