Yamaha 01V96i Reference Manual - Page 107

Transmitting Parameter Settings via MIDI (Bulk Dump)

107

01V96i—Reference Manual

MIDI

Transmitting Parameter

Settings via MIDI (Bulk

Dump)

You can back up data stored in the 01V96i, such as libraries

and Scenes, to an external MIDI device by using MIDI Bulk

Dump. In this way, you can later restore previous 01V96i set-

tings by transmitting this MIDI data back to the 01V96i.

1.

Press the DISPLAY ACCESS [DIO/SETUP] but-

ton repeatedly until the DIO/Setup |

MIDI/Host page appears, then specify ports

for transmission and reception of MIDI mes-

sages (see page 101).

2.

Make connections using the ports selected in

Step 1 so that the 01V96i can transmit and

receive MIDI messages to and from the exter-

nal device.

3.

Press the DISPLAY ACCESS [MIDI] button,

then press the [F4] button.

The MIDI | Bulk page appears.

The page includes the following parameters:

1

CATEGORY section

This section enables you to select data for transmission

and reception.

2

REQUEST

Move the cursor to this button, then press [ENTER] to

transmit messages from the 01V96i that request a second

01V96i (connected to the first 01V96i) to transmit the

data specified in the CATEGORY section. This button is

used primarily when two 01V96is are connected in cas-

cade.

3

TRANSMIT

Move the cursor to this button, then press [ENTER] to

transmit data specified in the CATEGORY section to an

external MIDI device.

4

INTERVAL

This parameter specifies the interval between data pack-

ets during bulk transmission in 50 millisecond steps. If

the external device drops part of the bulk data, increase

this parameter value.

4.

In the CATEGORY section, move the cursor to

the button of the data type you want to trans-

mit, then press [ENTER].

The following options are available:

• ALL

This button selects all data available for bulk dump. When

this button is turned on, all other buttons in this section

are turned off.

• SCENEMEM

This button selects Scene memories. You can select

Scenes you wish to transmit in the parameter box next to

the button.

• LIBRARY

This button selects libraries. You can select the type of

library in the TYPE parameter box (next to the button),

then specify the library number in the parameter box on

the right.

• BANK

This parameter enables you to select the User Defined

Key banks (KEYS UDEF), User Defined Remote Layer

banks (RMT UDEF), or User Assignable Layer banks

(USR LAYER) for bulk dump. You can select one of these

three types in the parameter box next to the button, and

select the banks in the parameter box on the right.

• SETUPMEM

This button selects the 01V96i setup data (i.e., system set-

tings).

•

PGM TABLE

This button selects the MIDI | Pgm Asgn page settings.

•

CTL TABLE

This button selects the MIDI | Ctl Asgn page settings.

• PLUG-IN

This button selects the settings of an optional card

installed in the slot.

Note:

Some of the data transmitted from the 01V96i to the

sequence software may occasionally drop out during Bulk Dump

transmission. To avoid this, we recommend that you use the Stu-

dio Manager software to store 01V96i data to an external device.

1

2

3

4

Note:

Data selected by the SETUPMEM button includes

MIDI transmission and reception port settings and message

settings. After you store to an external device bulk dump data

that has its reception disabled, if the 01V96i later starts to

receive this particular data, 01V96i bulk dump reception will

be turned off immediately, and the 01V96i will be unable to

receive subsequent data. Therefore, before you store the data

selected by the SETUPMEM button using Bulk Dump, be

sure to enable bulk data transmission and reception.

Section	Page
How to Use This Reference Manual	1
Contents	2
Contents of the Owner’s Manual (Booklet)	3
Function Tree	4
Control Surface & Rear Panel	6
Control Surface	6
Rear Panel	10
Analog I/O & Digital I/O	12
Analog Inputs & Outputs	12
Digital Inputs & Outputs	13
Converting Sampling Rates of Signals Received at I/O Card Inputs	14
Monitoring Digital Input Channel Status	14
Dithering Digital Outputs	15
Setting the Transfer Format for Higher Sampling Rates	16
Input Channels	17
About Input Channels	17
Setting the Input Channels from the Display	18
Setting the Input Channels from the Control Surface	25
Pairing Input Channels	26
Naming Input Channels	28
Bus Outs	29
About Stereo Out	29
Bus Out 1–8	29
Setting the Stereo Out and Bus Out 1–8 from the Display	30
Setting the Stereo Out and Bus Out 1–8 from the Control Surface	33
Pairing Buses or Aux Sends	33
Attenuating Output Signals	34
Naming the Stereo Out and Bus Outs	35
Aux Outs	36
Aux Out 1–8	36
Setting Aux Out 1–8 from the Display	36
Setting Aux Out 1–8 from the Control Surface	38
Setting Aux Send Levels	38
Viewing Aux Send Settings for Multiple Channels	40
Panning Aux Sends	41
Copying Channel Fader Positions to Aux Sends	42
Input & Output Patching	43
Input Patching	43
Output Patching	44
Patching Direct Outs	46
Insert Patching	47
Monitoring	49
Monitor	49
Monitor and Solo Setup	49
Using the Monitor	50
Using the Solo Function	51
Surround Pan	52
About Surround Pan	52
Setting Up and Selecting Surround Pan Modes	53
Surround Panning	56
Grouping Channels & Linking Parameters	59
Grouping & Linking	59
Using Fader Groups and Mute Groups	59
Using Fader Group Master	61
Using Mute Group Master	62
Linking EQ and Compressor Parameters	62
Internal Effects	64
About the Internal Effects	64
Using Effects Processors via Aux Sends	64
Inserting the Internal Effects into Channels	65
Editing Effects	66
About Add-On Effects	67
About Plug-Ins	67
Scene Memories	68
About Scene Memories	68
What is Stored in a Scene?	68
About Scene Numbers	68
Storing and Recalling Scenes	69
Auto Scene Memory Update	70
Fading Scenes	71
Recalling Scenes Safely	72
Sorting Scenes	72
Copying and Pasting a Scene (Global Paste)	73
Libraries	74
About the Libraries	74
General Library Operation	74
Using Libraries	75
Remote Control	83
About Remote Function	83
Pro Tools Remote Layer	83
Nuendo/Cubase Remote Layer	93
Other DAW Remote Layer	94
MIDI Remote Layer	94
Machine Control Function	98
MIDI	100
MIDI & the 01V96i	100
MIDI Port Setup	101
Assigning Scenes to Program Changes for Remote Recall	103
Assigning Parameters to Control Changes for Real-time Control	104
Controlling Parameters by Using Parameter Changes	106
Transmitting Parameter Settings via MIDI (Bulk Dump)	107
Other Functions	109
Setting Preferences	109
Creating a Custom Layer by Combining Channels (User Assignable Layer)	110
Cascading Consoles	111
Checking the Battery and the System Version	113
Calibrating the Faders	113
Index	115
Appendix: Parameter Lists	119
USER DEFINED KEYS	119
USER DEFINED KEYS Initial Assignments	121
Input Patch Parameters	121
Initial Input Patch Settings	123
Output Patch Parameters	125
Initial Output Patch Settings	127
User Defined Remote Layer Initial Bank Settings	128
Effects Parameters	132
Effects and tempo synchronization	146
Preset EQ Parameters	147
Preset Gate Parameters (fs = 44.1 kHz)	148
Preset Compressor Parameters (fs = 44.1 kHz)	149
Dynamics Parameters	151
Appendix: MIDI	156
Scene Memory to Program Change Table	156
Initial Parameter to Control Change Table	157
MIDI Data Format	173

Yamaha 01V96i Reference Manual - Page 107

Transmitting Parameter Settings via MIDI (Bulk Dump

Page 107 highlights