Yamaha 01V96i Reference Manual - Page 173

MIDI Data Format

173

01V96i—Reference Manual

Appendix: MIDI

MIDI Data Format

1. DATA FORMAT

1.1 CHANNEL MESSAGE

1.2 SYSTEM COMMON MESSAGE

1.3 SYSTEM REALTIME MESSAGE

1.4 EXCLUSIVE MESSAGE

1.4.1 Real Time System Exclusive

1.4.2 System Exclusive Message

1.4.2.1 Bulk Dump

The following data types of bulk dump are used on the 01V96i.

1.4.2.2 PARAMTER CHANGE

The following data types of parameter change are used by the 01V96i.

*

‘tx’ indicates that the data can be transmitted from the 01V96i, and

‘rx’ indicates that the data can be received by the 01V96i.

2. Format Details

2.1 NOTE OFF

(8n)

Reception

If [OTHER ECHO] is ON, these message are echoed from MIDI OUT.

If the [Rx CH] matches, these messages are received and used to control effects.

2.2 NOTE ON

(9n)

Reception

If [OTHER ECHO] is ON, these messages are echoed from MIDI OUT.

If the [Rx CH] matches, these messages are received and used to control effects.

2.3 CONTROL CHANGE

(Bn)

Reception

If [Control Change ECHO] is ON, these messages are echoed from MIDI OUT.

If [TABLE] is selected, these message are received if [Control Change Rx] is ON,

and will control parameters according to the [Control assign table] settings.

The parameters that can be set are defined in the Control Change Assign Pa-

rameter List.

If [NRPN] is selected, these messages are received if [Control Change Rx] is ON

and the [Rx CH] matches, and will control the parameter that is specified by the

four messages NRPN control number (62h, 63h) and Data Entry control num-

ber (06h, 26h). Parameter settings are defined in the Control Change Assign Pa-

rameter List.

Transmission

If [TABLE] is selected, operating a parameter specified in the [Control assign

table] will cause these messages to be transmitted if [Control Change Tx] is ON.

The parameters that can be specified are defined in the Control Change Assign

Parameter List.

If [NRPN] is selected, operating a specified parameter will cause data to be

transmitted on the [Tx CH] if [Control Change Tx] is ON, using the four mes-

sages NRPN control number (62h, 63h) and Data Entry control number (06h,

26h). Parameter settings are defined in the Control Change Assign Parameter

List.

This data cannot be transmitted via control change to Studio Manager since

there is no guarantee that the contents of the tables will match. (Parameter

Change messages will always be used.)

Command

rx/tx

function

8n NOTE OFF

rx

Control the internal effects

9n NOTE ON

rx

Control the internal effects

Bn CONTROL CHANGE

rx/tx

Control parameters

Cn PROGRAM CHANGE

rx/tx

Switch scene memories

Command

rx/tx

function

F1 MIDI TIME CODE QUARTER

FRAME

rx

MTC

Command

rx/tx

function

F8 TIMING CLOCK

rx

MIDI clock

FE ACTIVE SENSING

rx

Check MIDI cable connections

FF RESET

rx

Clear running status

Command

rx/tx

function

F0 7F dd 06 … F7 MMC

COMMAND

tx

MMC command

F0 7F dd 07 … F7 MMC RESPONSE

rx

MMC response

F0 7F dd 01 … F7 MIDI TIME CODE

rx

MTC full message

Command

rx/tx

function

F0 43 0n 7E … F7 BULK DUMP

DATA

rx/tx

BULK DUMP DATA

F0 43 2n 7E … F7 BULK DUMP

REQUEST

rx/tx

BULK DUMP REQUEST

Data name

tx/rx

function

‘m’

tx/rx

Scene Memory & Request

(compressed data)

‘S’

tx/rx

Setup Memory & Request

‘L’

tx/rx

User defined MIDI remote &

Request

‘V’

tx/rx

User defined keys & Request

‘U’

tx/rx

User assignable layer & Request

‘C’

tx/rx

Control change table & Request

‘P’

tx/rx

Program change table & Request

‘Q’

tx/rx

Equalizer library & Request

‘Y’

tx/rx

Compressor library & Request

‘G’

tx/rx

Gate library & Request

‘E’

tx/rx

Effect library & Request

‘H’

tx/rx

Channel library & Request

‘R’

tx/rx

Input patch library & Request

‘O’

tx/rx

Output patch library & Request

‘N’

tx/rx

Plug-in Effect Card Data & Request

Command

rx/tx

function

F0 43 1n 3E 0D … F7 RARAMETER

CHANGE

rx/tx

01V96i-specific parameter change

F0 43 3n 3E 0D … F7 PARAMETER

REQUEST

rx/tx

01V96i-specific parameter change

F0 43 1n 3E 7F … F7 PARAMETER

CHANGE

rx/tx

General purpose digital mixer

parameter change

F0 43 3n 3E 7F … F7 PARAMETER

REQUEST

rx/tx

General purpose digital mixer

parameter request

Type (HEX)

tx/rx

function

1 (01)

tx/rx

Edit buffer

2 (02)

tx/rx

Patch data

3 (03)

tx/rx

Setup data

4 (04)

tx/rx

Backup data

16 (10)

tx/rx

Function (recall, store, title, clear)

17 (11)

rx

Function (pair, copy)

18 (12)

rx

Function (effect)

19 (13)

tx/rx

Sort table

20 (14)

tx/rx

Function (attribute, link)

32 (20)

rx

Key remote

33 (21)

tx/rx

Remote meter

34 (22)

tx/rx

Remote time counter

STATUS

1000nnnn 8n

Note off message

DATA

0nnnnnnn nn

Note number

0vvvvvvv vv

Velocity(ignored)

STATUS

1001nnnn 9n

Note on message

DATA

0nnnnnnn nn

Note number

0vvvvvvv vv

Velocity(1-127:on, 0:off)

Section	Page
How to Use This Reference Manual	1
Contents	2
Contents of the Owner’s Manual (Booklet)	3
Function Tree	4
Control Surface & Rear Panel	6
Control Surface	6
Rear Panel	10
Analog I/O & Digital I/O	12
Analog Inputs & Outputs	12
Digital Inputs & Outputs	13
Converting Sampling Rates of Signals Received at I/O Card Inputs	14
Monitoring Digital Input Channel Status	14
Dithering Digital Outputs	15
Setting the Transfer Format for Higher Sampling Rates	16
Input Channels	17
About Input Channels	17
Setting the Input Channels from the Display	18
Setting the Input Channels from the Control Surface	25
Pairing Input Channels	26
Naming Input Channels	28
Bus Outs	29
About Stereo Out	29
Bus Out 1–8	29
Setting the Stereo Out and Bus Out 1–8 from the Display	30
Setting the Stereo Out and Bus Out 1–8 from the Control Surface	33
Pairing Buses or Aux Sends	33
Attenuating Output Signals	34
Naming the Stereo Out and Bus Outs	35
Aux Outs	36
Aux Out 1–8	36
Setting Aux Out 1–8 from the Display	36
Setting Aux Out 1–8 from the Control Surface	38
Setting Aux Send Levels	38
Viewing Aux Send Settings for Multiple Channels	40
Panning Aux Sends	41
Copying Channel Fader Positions to Aux Sends	42
Input & Output Patching	43
Input Patching	43
Output Patching	44
Patching Direct Outs	46
Insert Patching	47
Monitoring	49
Monitor	49
Monitor and Solo Setup	49
Using the Monitor	50
Using the Solo Function	51
Surround Pan	52
About Surround Pan	52
Setting Up and Selecting Surround Pan Modes	53
Surround Panning	56
Grouping Channels & Linking Parameters	59
Grouping & Linking	59
Using Fader Groups and Mute Groups	59
Using Fader Group Master	61
Using Mute Group Master	62
Linking EQ and Compressor Parameters	62
Internal Effects	64
About the Internal Effects	64
Using Effects Processors via Aux Sends	64
Inserting the Internal Effects into Channels	65
Editing Effects	66
About Add-On Effects	67
About Plug-Ins	67
Scene Memories	68
About Scene Memories	68
What is Stored in a Scene?	68
About Scene Numbers	68
Storing and Recalling Scenes	69
Auto Scene Memory Update	70
Fading Scenes	71
Recalling Scenes Safely	72
Sorting Scenes	72
Copying and Pasting a Scene (Global Paste)	73
Libraries	74
About the Libraries	74
General Library Operation	74
Using Libraries	75
Remote Control	83
About Remote Function	83
Pro Tools Remote Layer	83
Nuendo/Cubase Remote Layer	93
Other DAW Remote Layer	94
MIDI Remote Layer	94
Machine Control Function	98
MIDI	100
MIDI & the 01V96i	100
MIDI Port Setup	101
Assigning Scenes to Program Changes for Remote Recall	103
Assigning Parameters to Control Changes for Real-time Control	104
Controlling Parameters by Using Parameter Changes	106
Transmitting Parameter Settings via MIDI (Bulk Dump)	107
Other Functions	109
Setting Preferences	109
Creating a Custom Layer by Combining Channels (User Assignable Layer)	110
Cascading Consoles	111
Checking the Battery and the System Version	113
Calibrating the Faders	113
Index	115
Appendix: Parameter Lists	119
USER DEFINED KEYS	119
USER DEFINED KEYS Initial Assignments	121
Input Patch Parameters	121
Initial Input Patch Settings	123
Output Patch Parameters	125
Initial Output Patch Settings	127
User Defined Remote Layer Initial Bank Settings	128
Effects Parameters	132
Effects and tempo synchronization	146
Preset EQ Parameters	147
Preset Gate Parameters (fs = 44.1 kHz)	148
Preset Compressor Parameters (fs = 44.1 kHz)	149
Dynamics Parameters	151
Appendix: MIDI	156
Scene Memory to Program Change Table	156
Initial Parameter to Control Change Table	157
MIDI Data Format	173

Yamaha 01V96i Reference Manual - Page 173

MIDI Data Format, DATA FORMAT, Format Details - digital mixer

Page 173 highlights