Yamaha 01V96i Reference Manual - Page 75

Using Libraries

75

01V96i—Reference Manual

Libraries

Using Libraries

Channel Library

Channel library enables you to store and recall Input Channel

and Output Channel parameter settings. The library contains

two preset memories and 127 user (readable & writable)

memories.

You can recall only the settings for the currently-selected

channels from the Channel library. For example, you cannot

recall Input Channel 1–32 settings to ST IN Channels 1–4,

Bus Outs 1–8, Aux Outs 1–8, or Stereo Out, with the excep-

tion that memories #0 and #1 can be recalled to any channels.

Follow the steps below to use the Channel library.

1.

Press the DISPLAY ACCESS [VIEW] button

repeatedly until the View | Library page

appears.

1

SEL CH

This parameter indicates the currently-selected channel.

2

CURRENT CONFIGURATION section

If the currently-selected channel is an Input Channel

(1–32) or ST IN Channels (1–4), its Surround mode and

Aux configuration information is displayed here.

3

Level meters

These meters indicate the levels of the currently-selected

channel and the available partner.

4

STORED FROM

This parameter indicates the channel for which the set-

tings were originally stored in the selected library mem-

ory. If the currently-selected library memory contains

Input Channel 1–32 and ST IN Channels 1–4 settings, its

Surround mode and Aux pairing information are also

displayed below this parameter.

2.

Use the LAYER buttons to select layers, then

press the [SEL] buttons to select channels.

For details on the Store and Recall functions, see “General

Library Operation” on page 74.

If the selected memory’s channel type does not match the

type of the destination channel, an alarm mark (

) and

the word “CONFLICT” appear next to the STORED

FROM parameter. These alarms indicate that you tried to

recall unrecallable channel settings to the cur-

rently-selected channel.

The alarm indicators also appear when the Surround

mode, Aux pair, and other non-channel parameter set-

tings originally stored in the memory do not match those

for the destination channel. However, if the channel type

of the memory and that of the destination channel match,

you can recall the settings even with the alarm indicators

displayed. (For unmatched parameter settings, the

01V96i will use the settings in the memory that is to be

recalled.)

The following preset memories are available for the

Channel library.

Input Patch Library

The Input Patch library enables you to store and recall all

Input Patch settings. The library contains one preset memory

and 32 user (readable & writable) memories.

To access the Input Patch library, press the DISPLAY ACCESS

[PATCH] button repeatedly until the Patch | IN LIB page

appears. For details on storing and recalling memories, see

“General Library Operation” on page 74.

Input Patch preset memory #0 contains the following settings:

1

2

3

4

No.

Preset Name

Description

0

Reset (–



dB)

This preset memory resets all

parameters of the cur-

rently-selected channel to their

initial values and sets the chan-

nel fader level to (–



dB).

1

Reset (0 dB)

This preset memory resets all

parameters of the cur-

rently-selected channel to their

initial values and sets the chan-

nel fader level to 0 dB (i.e.,

nominal).

Input Channels 1–16

INPUT connectors 1–16


ADAT IN Channels 1–8


Slot Channels 1–8

ST IN Channels 1–4

Internal Effects Processor 1–4

Outputs 1 & 2

Section	Page
How to Use This Reference Manual	1
Contents	2
Contents of the Owner’s Manual (Booklet)	3
Function Tree	4
Control Surface & Rear Panel	6
Control Surface	6
Rear Panel	10
Analog I/O & Digital I/O	12
Analog Inputs & Outputs	12
Digital Inputs & Outputs	13
Converting Sampling Rates of Signals Received at I/O Card Inputs	14
Monitoring Digital Input Channel Status	14
Dithering Digital Outputs	15
Setting the Transfer Format for Higher Sampling Rates	16
Input Channels	17
About Input Channels	17
Setting the Input Channels from the Display	18
Setting the Input Channels from the Control Surface	25
Pairing Input Channels	26
Naming Input Channels	28
Bus Outs	29
About Stereo Out	29
Bus Out 1–8	29
Setting the Stereo Out and Bus Out 1–8 from the Display	30
Setting the Stereo Out and Bus Out 1–8 from the Control Surface	33
Pairing Buses or Aux Sends	33
Attenuating Output Signals	34
Naming the Stereo Out and Bus Outs	35
Aux Outs	36
Aux Out 1–8	36
Setting Aux Out 1–8 from the Display	36
Setting Aux Out 1–8 from the Control Surface	38
Setting Aux Send Levels	38
Viewing Aux Send Settings for Multiple Channels	40
Panning Aux Sends	41
Copying Channel Fader Positions to Aux Sends	42
Input & Output Patching	43
Input Patching	43
Output Patching	44
Patching Direct Outs	46
Insert Patching	47
Monitoring	49
Monitor	49
Monitor and Solo Setup	49
Using the Monitor	50
Using the Solo Function	51
Surround Pan	52
About Surround Pan	52
Setting Up and Selecting Surround Pan Modes	53
Surround Panning	56
Grouping Channels & Linking Parameters	59
Grouping & Linking	59
Using Fader Groups and Mute Groups	59
Using Fader Group Master	61
Using Mute Group Master	62
Linking EQ and Compressor Parameters	62
Internal Effects	64
About the Internal Effects	64
Using Effects Processors via Aux Sends	64
Inserting the Internal Effects into Channels	65
Editing Effects	66
About Add-On Effects	67
About Plug-Ins	67
Scene Memories	68
About Scene Memories	68
What is Stored in a Scene?	68
About Scene Numbers	68
Storing and Recalling Scenes	69
Auto Scene Memory Update	70
Fading Scenes	71
Recalling Scenes Safely	72
Sorting Scenes	72
Copying and Pasting a Scene (Global Paste)	73
Libraries	74
About the Libraries	74
General Library Operation	74
Using Libraries	75
Remote Control	83
About Remote Function	83
Pro Tools Remote Layer	83
Nuendo/Cubase Remote Layer	93
Other DAW Remote Layer	94
MIDI Remote Layer	94
Machine Control Function	98
MIDI	100
MIDI & the 01V96i	100
MIDI Port Setup	101
Assigning Scenes to Program Changes for Remote Recall	103
Assigning Parameters to Control Changes for Real-time Control	104
Controlling Parameters by Using Parameter Changes	106
Transmitting Parameter Settings via MIDI (Bulk Dump)	107
Other Functions	109
Setting Preferences	109
Creating a Custom Layer by Combining Channels (User Assignable Layer)	110
Cascading Consoles	111
Checking the Battery and the System Version	113
Calibrating the Faders	113
Index	115
Appendix: Parameter Lists	119
USER DEFINED KEYS	119
USER DEFINED KEYS Initial Assignments	121
Input Patch Parameters	121
Initial Input Patch Settings	123
Output Patch Parameters	125
Initial Output Patch Settings	127
User Defined Remote Layer Initial Bank Settings	128
Effects Parameters	132
Effects and tempo synchronization	146
Preset EQ Parameters	147
Preset Gate Parameters (fs = 44.1 kHz)	148
Preset Compressor Parameters (fs = 44.1 kHz)	149
Dynamics Parameters	151
Appendix: MIDI	156
Scene Memory to Program Change Table	156
Initial Parameter to Control Change Table	157
MIDI Data Format	173

Yamaha 01V96i Reference Manual - Page 75

Using Libraries, Channel Library, Input Patch Library

Page 75 highlights