Home » Yamaha Manuals » Audio Mixers » Yamaha 01V96i » Manual Viewer

Yamaha 01V96i Reference Manual - Page 112

ton repeatedly to display the DIO/Setup, adjust the Attenuators using the parameter

Get Yamaha 01V96i PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

112 Other Functions Bus signals via the ADAT IN and OUT connectors and two 8-channel digital I/O cards (such as MY8-AT). 8. Press the DISPLAY ACCESS [DIO/SETUP] button repeatedly to display the DIO/Setup | MIDI/Host page, then set the Cascade Link parameter to "MIDI." Note: Be sure to patch the slave Bus signals to the same Buses on the master unit. Incorrect patching will result in an incorrect cascade connection. 7. On the master unit, press the DISPLAY ACCESS [DIO/SETUP] button repeatedly until the DIO/Setup | Cascade page appears, then adjust the Attenuators using the parameter controls. The DIO/Setup | Cascade page enables you to adjust the level of signals input to the Cascade Bus using the dedicated attenuators. You can also turn the Cascade Buses on or off using the buttons below the parameter controls. 9. Repeat Step 8 for the master unit. After Steps 8 and 9, the slave unit will be able to transmit and receive MIDI messages. 10. To match the parameters of both 01V96is, locate the DIO/Setup | MIDI/Host page on the copy source unit. Move the cursor to the TRANSMIT button for the SYNC parameter, then press [ENTER]. Parameters for cascade link (page 111) will be copied to the other 01V96i via the REMOTE connector. If you select the REQUEST button instead of the TRANSMIT button for the SYNC parameter, you can reverse the copy direction. At this point, Bus 1-8, Aux 1-4, and the Stereo Bus on both 01V96is are integrated, and the data is output via Bus Outs 1-8, Aux Outs 1-4, and the Stereo Out on the master unit. If you solo channels on one of the 01V96is, you can monitor the soloed signals via the Monitor outputs. 01V96i-Reference Manual

Section	Page
How to Use This Reference Manual	1
Contents	2
Contents of the Owner’s Manual (Booklet)	3
Function Tree	4
Control Surface & Rear Panel	6
Control Surface	6
Rear Panel	10
Analog I/O & Digital I/O	12
Analog Inputs & Outputs	12
Digital Inputs & Outputs	13
Converting Sampling Rates of Signals Received at I/O Card Inputs	14
Monitoring Digital Input Channel Status	14
Dithering Digital Outputs	15
Setting the Transfer Format for Higher Sampling Rates	16
Input Channels	17
About Input Channels	17
Setting the Input Channels from the Display	18
Setting the Input Channels from the Control Surface	25
Pairing Input Channels	26
Naming Input Channels	28
Bus Outs	29
About Stereo Out	29
Bus Out 1–8	29
Setting the Stereo Out and Bus Out 1–8 from the Display	30
Setting the Stereo Out and Bus Out 1–8 from the Control Surface	33
Pairing Buses or Aux Sends	33
Attenuating Output Signals	34
Naming the Stereo Out and Bus Outs	35
Aux Outs	36
Aux Out 1–8	36
Setting Aux Out 1–8 from the Display	36
Setting Aux Out 1–8 from the Control Surface	38
Setting Aux Send Levels	38
Viewing Aux Send Settings for Multiple Channels	40
Panning Aux Sends	41
Copying Channel Fader Positions to Aux Sends	42
Input & Output Patching	43
Input Patching	43
Output Patching	44
Patching Direct Outs	46
Insert Patching	47
Monitoring	49
Monitor	49
Monitor and Solo Setup	49
Using the Monitor	50
Using the Solo Function	51
Surround Pan	52
About Surround Pan	52
Setting Up and Selecting Surround Pan Modes	53
Surround Panning	56
Grouping Channels & Linking Parameters	59
Grouping & Linking	59
Using Fader Groups and Mute Groups	59
Using Fader Group Master	61
Using Mute Group Master	62
Linking EQ and Compressor Parameters	62
Internal Effects	64
About the Internal Effects	64
Using Effects Processors via Aux Sends	64
Inserting the Internal Effects into Channels	65
Editing Effects	66
About Add-On Effects	67
About Plug-Ins	67
Scene Memories	68
About Scene Memories	68
What is Stored in a Scene?	68
About Scene Numbers	68
Storing and Recalling Scenes	69
Auto Scene Memory Update	70
Fading Scenes	71
Recalling Scenes Safely	72
Sorting Scenes	72
Copying and Pasting a Scene (Global Paste)	73
Libraries	74
About the Libraries	74
General Library Operation	74
Using Libraries	75
Remote Control	83
About Remote Function	83
Pro Tools Remote Layer	83
Nuendo/Cubase Remote Layer	93
Other DAW Remote Layer	94
MIDI Remote Layer	94
Machine Control Function	98
MIDI	100
MIDI & the 01V96i	100
MIDI Port Setup	101
Assigning Scenes to Program Changes for Remote Recall	103
Assigning Parameters to Control Changes for Real-time Control	104
Controlling Parameters by Using Parameter Changes	106
Transmitting Parameter Settings via MIDI (Bulk Dump)	107
Other Functions	109
Setting Preferences	109
Creating a Custom Layer by Combining Channels (User Assignable Layer)	110
Cascading Consoles	111
Checking the Battery and the System Version	113
Calibrating the Faders	113
Index	115
Appendix: Parameter Lists	119
USER DEFINED KEYS	119
USER DEFINED KEYS Initial Assignments	121
Input Patch Parameters	121
Initial Input Patch Settings	123
Output Patch Parameters	125
Initial Output Patch Settings	127
User Defined Remote Layer Initial Bank Settings	128
Effects Parameters	132
Effects and tempo synchronization	146
Preset EQ Parameters	147
Preset Gate Parameters (fs = 44.1 kHz)	148
Preset Compressor Parameters (fs = 44.1 kHz)	149
Dynamics Parameters	151
Appendix: MIDI	156
Scene Memory to Program Change Table	156
Initial Parameter to Control Change Table	157
MIDI Data Format	173